Votes - 2, Average rating: 3.5 ( )

Manafacture: Conair File size: 1.77 mb File name: symphony2210---user-guide.pdf Language of manual:

“The phone Check that the base unit’s mains power adapter is does not ring” plugged in and power is switched on. The base unit needs mains power for normal operation of the phone — not just for charging the batteries. Make sure you’re using the telephone line cable that was supplied with your DECT Phone. Other telephone line cables might not work. Check that the total REN value of all equipment connected to your telephone line is no more than 4 (see page 3). Disconnect one or more telephones and see whether that helps. “There is inter- Move the handset closer to the base unit, or to a ference and different position. noise on the Try moving the base unit so that it’s not near other line.” electrical equipment, such as a television or a computer. http:/ / online .com/ 45 Color profile: Disabled Composite Default screen Troubleshooting You’ll get the best results if you site the base unit as high as possible. For example, in a two-storey house, the first-floor landing is an ideal place for the base unit. “My call was cut Move the handset closer to the base unit before you try off when I went again to make a call. out of range. Now I can’t use my handset.” “I hear ‘beeps’ You may be going out of range of the base unit. Move from my closer, or your call may be cut off. handset while Check the ‘battery charge level’ symbol on the display. I’m on a call.” If it is low, recharge the batteries. “The Caller Display feature isn’t working.” You need to subscribe to the Caller Display feature. Contact your service provider. The caller may have withheld their number. Or they may be calling from a network that does not transmit the Caller ID (for example, it may be an international call) . “When I try to If you have more than one handset registered to your make a call, I base unit, make sure that another handset isn’t already hear Busy using the line. tone.” “The volume in Make sure you’re holding the earpiece correctly over the earpiece is your ear. low when I’m on a call.” Adjust the volume using the button. ^ or Ў 46 Binatone Help Line: 0845 345 9677 (Local Call rate) Color profile: Disabled Composite Default screen Troubleshooting Using a multi-handset system “I can’t transfer Make sure the other handset is in range of the base unit. a call.” Make sure you’re dialling the correct number for the other handset ( 1 to 5) . Batteries “The handset‘s Before you first used the handset, you should have left it batteries are on the base unit or charger pod for up to 15 hours to running low charge the batteries fully. within an You may need to replace the batteries (see below). hour or two.” Clean the battery charging contacts on the base unit with a dry cloth. “I try to recharge the batteries, but I still get a warning that they are low.” Check the connections between the base unit and the mains power socket. You need to replace the batteries. To find out how to obtain replacements, call 0845 345 9677, between 9.00 am and 5.00 pm, Monday to Friday. Dispose of used batteries safely — never burn them, or put them where they could get punctured. ALWAYS use the batteries supplied with your Symphony 2210 — other batteries may burst, causing damage. PBX use “The Recall You may need to change the recall signal length from function doesn’t its default short. Consult your PBX documentation seem to work.” help if necessary. To change the recall setting, please see page 40 . 47 Color profile: Disabled Composite Default screen Troubleshooting “Last Number Redial and/or memory dialling don’t work on a PBX.” When you first make a call, after keying in the outside line access code (e.g. 9), press and hold the Last Number Redial button until a P appears on the display. This inserts a pause between the access code and the telephone number. You should later be able to redial the number. When storing numbers in memory, you can include the outside line access code (e.g. 9) with each number. If your PBX requires you to wait for a second Dial tone before dialling the telephone number, press and hold the Last Number Redial button for a pause between the access code and the number. If the fault persists … Disconnect all other instruments connected to the same line as the Symphony 2210 and see whether you can make a call. Disconnect the base unit from the telephone line and plug a different phone into the master telephone socket. Try making a call. If this works, the line is OK. If the call does not work, and you are using a two-way socket adapter, remove it and plug a telephone directly into the socket. If the call now works, the adapter may be faulty. If you cannot make a call, the fault may be on the exchange line. Contact the service provider. If you still cannot identify the cause of the problem, contact the Help Line on 0845 345 9677. 48 Binatone Help Line: 0845 345 9677 (Local Call rate) Color profile: Generic CMYK printer profile Composite Default screen Cleaning and care ¦ Don’t clean any part of yo...

Download now

Please, enter two numbers from picture: