Votes - , Average rating: ( )

User manual iHome, model IP23

Manafacture: iHome
File size: 122.77 kb
File name: iP23_IB_Eng_02.10.11_1.pdf

Language of manual:

The document is loading, please wait

Download nowClose

The document is loading, please wait

Download nowClose

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. Battery Warning For models that require more than one battery • Do not mix with used or other battery types/brands • Replace all batteries at the same time • Do not open batteries • Do not dispose of in fire • Do not heat above 75.C (167.F) • Do not expose contents to water • Do not charge or recharge • Do not install backwards Controls and Indicators Controls and Indicators Top Panel Dock Lower Volume Button Sleep Button Raise Volume Button Alarm Reset / Power Button Forward Button Alarm 1 Button Alarm 2 Button Reverse Button Play/Pause Button Snooze/Dimmer Button Rear Panel Aux Line-in Jack Time Zone Button Time Sync/Set Button DST Switch AC Adaptor Jack 1 iP23 Quick Start iP23 Quick Start 2: inserts Attach AC adaptor cable to jack on back of the unit and plug the other end into a wall socket to play and charge iPhone/iPod. Insert playing iPhone/iPod into the dock (must not be in a “skin” or case). Your audio will play through the unit. Press volume buttons to adjust volume. iPhone/iPod will charge while docked. 3: iPhone/iPod Select the dock insert for your iPhone/iPod model from the table below and place insert in dock. To remove insert, place thumbnail in slot and gently pull upwards. iPhone 3G insert 15 iPhone 3G/3GS iPod touch 2G insert 16 iPod touch 2G/3G iPhone 4 insert 19 nano 6G/touch 4G insert 20 nano 6G iPod touch 4G iPhone 4 nano 5G insert 18 nano 5G Use this insert For this iPhone / iPod RESET RESET 1: power Note: An insert provides the best stability and safety for your iPhone/iPod, but you can safely dock your iPhone or iPod without an insert, provided you always do so with care. If you prefer to use an insert and don’t have one for your model, please visit or call iHome toll free at 800-288-2792 to purchase one. 4:time sync • Make sure your iPhone or iPod is properly docked • Press the Time Sync/Set button on the back of the unit • “SYNC” will appear on the display, followed by “DONE” • If “FAIL” appears, try again with a different iPhone or iPod, or see Setting Time Manually (page 4). 2 Display Display PM Indicator Time Display Sleep indicator Buzzer indicator Battery Low Indicator Alarm 1, Alarm 2 Indicators iPod Indicator Installing/Replacing Clock Backup Batteries The unit uses 2 AA batteries (installed) for backup to provide continuous alarm operation and clock settings in the event of a power failure. If the backup batteries have been installed and a power failure occurs or the AC adaptor is accidentally disconnected, the display backlight will not remain lit, but current time and alarm time settings will be temporarily maintained. Otherwise, you must reset the time and alarm settings. Note: You should replace backup batteries when the Battery Low Indicator flashes on the display. 1. Please make sure the AC adaptor is connected. Otherwise all settings may be lost during battery replacement. 2. Open backup battery compartment door located on the bottom of the unit. 3. Insert 2 “AA” batteries, checking the + and – ends of the batteries match the diagram to the right. We recommend alkaline batteries for longer life time. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries. 4. Close the compartment cover. Note: Make sure you dispose of batteries properly (see your local regulations). 3 Operating the Unit Operating the Unit This unit has a PRESET Clock: the time is already preset to Eastern time at the factory. Simply match the time zone setting to where you live. 1. Depending on your location and whether or not Daylight Saving Time (DST) is in effect, set the DST Switch located on the back of the unit to +1 to add an hour or to -1 to subtract an hour to/from the currently displayed time. 2. Press and hold the Time Zone Button located on the back of the unit until the current time zone flashes. The unit will beep. Press the or Button to select your time zone. 3. Press the Time Zone Button again (or no button within 10 seconds) to exit the setting mode. 2 beeps will confirm Time Zone setting is complete. 4. If the displayed time is not correct, see instructions below to set the clock. Setting the Clock Time Using Time Sync The Time Sync feature allows you to sync the time setting on the unit to the time on your iPhone or recent model iPod (iPod touch, iPod nano and iPod Classic; older iPod models such as iPod mini do not support this feature). 1. Press the Time Sync/Set Button located at the back of the unit. “Sync” flashes on the display and a beep sounds. 2. Once sync is completed, “DONE” appears on the display followed by 2 beeps indicating time sync is complete. The updated time will appear on the display. 3. If sync was not successful, “FAIL” will appear on the display and a long beep will sound. If this happens, please try again, with a different iPhone or iPod if needed. If sync still fa...