Votes - 4, Average rating: 3.5 ( )

Manafacture: iHome File size: 255.55 kb File name: 96a3564e-1ef5-43f6-ae64-2afb685da465.pdf Language of manual:

For models that require more than one battery • Do not mix with used or other battery types/brands • Replace all cells at the same time • Do not open batteries • Do not dispose of in fire • Do not heat above 75C (167F) • Do not expose contents to water • Do not charge or recharge • Do not install backwards iP11 Quick Start 2:inserts Select the dock insert for your iPhone or iPod model from the table below and place insert in dock. Never dock an iPhone or iPod without an insert in place. 3:iPhone/iPod Insert iPhone/iPod into dock with proper insert (iPhone/iPod must not be in a skin or case). iPhone/iPod will charge while docked. Press iPhone/iPod Button on iP11 to play iPhone/iPod. 4:time sync • Make sure your iPhone/iPod is docked properly (see above). • Press the Time sync/set button located on the back of the unit. A cursor will cycle across the display, indicating sync mode. • Two beeps will confirm successful syncing and the time will update. • See “Setting the Clock” on page 5 to set clock manually. 1:power Attach AC adaptor cable to jack on back of the iP11 and plug the other end into a wall socket. DC 10Vline in dst -1 +1 on o NOTE: If you do not have an insert for your iPhone/iPod, please visit or call iHome toll free at 800-288-2792 to purchase one iPod Touch 2G iPhone 3G Insert 15 nano 5G insert 18 nano 5GiPhone 3G/ 3GS iiPod touch 2G insert 16 For this iPhone/iPod Use this insert 1 Controls and Indicators Controls and Indicators Alarm Set / Front Panel Alarm On/Off Button . Dock Power Off / . iPhone/iPod Play/Pause Button Alarm Reset Button . . Hour Set Button Snooze/Dimmer Button . . Sleep/Minute Set Button . Volume + Button . Volume - Button Back Panel Time sync/set Button . DST Switch . DC 10Vline in dst -1 +1 on o . EXB Expanded Bass Switch . DC Jack Line-in Jack . 2 iP11 Display iP11 Display Alarm IndicatorTime Display PM Indicator Battery Low Indicator Daylight Saving Time Indicator iPhone/iPod Indicator Sleep Indicator Install Clock Backup Battery The iP11 uses a CR2032 button cell backup battery system to provide continuous alarm operation and clock settings in the event of a power failure. If the Backup Battery has been installed and a power failure occurs or the AC adaptor is accidentally disconnected, the display backlight will not remain lit, but current time and alarm time settings will be temporarily maintained. Otherwise, you must reset the time and alarm settings. 1. Please make sure the AC adaptor is connected. Otherwise all settings may be lost during battery replacement. 2. Open backup battery compartment door located on the backside of the unit. 3. Insert one CR2032 button cell battery, checking that the polarity (+ and – sides of the battery) matches the drawing in the battery compartment. Close the compartment door. Note: Make sure you dispose of batteries properly (see your local regulations). Installing Backup Battery . 3 Setting the Clock Setting the Clock Setting the Clock Time 1. Press and hold the . Time sync/set Button for 2 seconds until the display flashes. Press the . Hour Set Button until the current hour is displayed. Next, press the . Sleep/Minute Set Button to set the current minute. 2. Press the . Time sync/set Button again to confirm the clock setting. You should hear 2 beeps indicating the clock time is set. 3. For 12 hour or 24 hour time format setting: Press the . Alarm Set Button during time setting to set 12-hour or 24-hour display format. Remember to set the correct AM or PM time (an icon to the right of the time display is the PM indicator; there is no AM indicator). 4. During daylight saving time, set the . DST Switch located on the backside of the unit to +1 to advance the time one hour. The DST Icon will appear next to the time display to indicate DST is on. Set the switch to -1 to quickly set the time back one hour at the end of daylight saving time. Using the Time Sync Feature The iP11 Time Sync feature allows you to sync the time setting on the iP11 to the time from your iPhone or recent model iPod (iPod Touch, iPod Nano and iPod Classic; older iPod models such as iPod mini do not support this feature). 1. Dock your iPhone using the proper insert. 2. Press the . Time sync/set Button to sync the iP11 clock to the time on your iPhone/iPod. The display will show a moving cursor, indicating the unit is syncing. When successfully completed, two beeps will confirm the time has been synced. Retry if sync is not successful. Note: iPhone time is automatically updated to the correct time via cell phone towers. The time on your iPod is accurate only to the time on the computer the last time the iPod was synced to it. An iPhone or iPod cannot sync to exact seconds; it’s possible to have up to 59 seconds difference between the iP11 and synced iPhone or iPod. 4 Charging your iPhone/iPod Charging your iPhone/iPod Note: Please make sure you are using the correct insert for your iPhone/iPod (see page 1) and that it is properly docked into the ...

Download now

Please, enter two numbers from picture: