Votes - , Average rating: ( )

User manual iHome, model IP43 IP43

Manafacture: iHome
File size: 343.39 kb
File name: iP43_IB_for_web.pdf

Language of manual:

The document is loading, please wait

Download nowClose

The document is loading, please wait

Download nowClose

Service methods not covered in the operating instructions should be referred to qualified service personnel. Questions? Visit 9 Troubleshooting Possible Problem Solution Symptom iP43 does not turn on AC adaptor isn't plugged into a working wall Plug the AC adaptor into a working wall socket and plug the socket or not plugged into the power supply connector into the supply jack on the unitjack on back of the unit iP43 doesn’t respond If unit is plugged in and doesn't respond, try resetting the unit by iP43 requires a reset following these steps: a) remove iPhone/iPod from dock b) unplug unit from power source c) remove back up batteries d) wait a few minutes, then resume use Remove your iPhone/iPod from the dock and check for obstruction on the connectors in the dock and on your iPhone/iPod. Then reseat it in the dock. iPhone/iPod is not docked properly Battery Low icon Batteries are weak Replace with new batteries always flashing Batteries were not installed properly Check to make sure the polarity ( + and – ends) matches the diagram in the battery compartment iPhone/iPod does iPhone/iPod is not docked properly Remove your iPhone/iPod from the dock and check for obstruction on the connectors in the dock and on your iPhone/iPod. Then reseat it in the dock. not respond to the unit/iPod is playing Your iPhone/iPod software is too old Upgrade software on your iPhone/iPod via iTunes on your but no sound comes computer out iPhone/iPod is locked up/plays but no Check the volume setting. Make sure your iPhone/iPod is working sound comes out properly before docking into the unit. Please refer to your iPhone/iPod manual for details. See above for software upgrade information. You may need to reset your iPhone/iPod. Refer to your iPhone or iPod user guide for details on how to perform a reset. Using 1st or 2nd generation iPod, iPod iP43 cannot control those iPod models or other devices. Shuffle or other devices. iP43/iPhone/iPod The iP43 is reacting to external interference Move unit away from potential sources of external interference such performance is erratic as computers, modems, wireless devices (routers) or fluorescent light. Volume is set too low on iP43 Make sure volume is turned up No sound from iP43 iPhone/iPod iPhone/iPod is not docked properly Remove your iPhone/iPod from the dock and check for didn’t obstruction on the connectors in the dock and on your charge up iPhone/iPod. Then reseat it in the dock. Please make sure your iPhone/iPod is working properly before docking into the unit. Please refer to your iPhone/iPod manual for iPhone/iPod battery has problem iPhone/iPod is locked up/ frozen details. 10 Troubleshooting Symptom Possible Problem Solution Sound is distorted Volume level is set too high Decrease the volume Sound source is distorted If the iPhone/iPod original sound source (MP3) is old or of poor quality, distortion and noise are easily noticed with high-power speakers. Try updating the sound file from a trusted source such as iTunes. If you are using an external sound source like older generation of iPod or iPod Shuffle, try reducing the output volume on the device itself. Also try turning bass boost OFF. EQ settings are too high. Lower EQ settings. Unit/adaptor gets warm after extended play at high volume This is normal Turn unit off for a while or lower volume Snooze time is too long/short Custom snooze time not set Press and hold Snooze button then turn Set Wheel to adjust Alarm not working AM/PM time/alarm time not set correctly When setting clock or alarm time, take note of the AM/PM indicators Alarm time or source selected for alarm 2 or alarm 3, not alarm 1, etc. Make sure to set the alarm time and source for the alarm icon 1, 2 or 3 that is shown on the clock display 7-5-2 days setting is not correct 7 days is every day alarm, 5 days is Mon-Fri, and 2 days is Sat-Sun. See page 5 for setting alarms. Calendar is not set correctly, which can affect 7/5/2 day alarm operation See page 4 for Time/Calendar setting section. Time sync didn’t work Older iPod models such as iPod mini do not support time sync function Make sure you are using an iPhone or newer iPod such as touch, nano or classic. If not available, set time manually (see page 4). 11 Limited 1 Year Warranty Information iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of 1 Year from the date of original purchase. Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased. Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period, SDI Technologies will repair or, at its discretion, replace this product without charge (except for a $15.00 charge for handling, packing, return UPS/postage, and ...