Votes - 3, Average rating: 3
(
)
)
|
manual abstract
Replace alarm settings will be retained during a supply. The LED display will not be operational. necessary for the unit to function. Aerials The wire aerial located on the rear of the CR980 is for wire should be fully extended and positioned for optimum There is a built in ferrite aerial for MW and LW stations. Rotate to the position giving best reception. Important If an alarm time has not been set and the Function switch is left in the 'Auto' or 'Alarm' position, the alarm/radio will operate at 12.00 midnight. If you do not require the alarm function, ensure that the Function switch is correctly set to the 'Off' position. The display alarm indicators will be switched off. If you need any further advice, please call our Technical Helpline on 0181 758 0338 (Mon-Fri) 4 Operating The radio is equipped programme of your The FM waveband external aerial wire This should be uncoiled and LW wavebands use an reception, it may be necessary Connect the mains plug to a wall Set the Waveband switch to FM, MW or LW and the Function switch to 'On' . The Volume control should be adjusted as required. Tune the radio to the desired programme by adjusting control. To switch off the radio, set the Function switch to 'Off' . If the radio does not switch off this may be caused by inadvertent operation of the Sleep function. Press the Time/Alarm off button once to cancel the sleep function and switch the radio off. Setting the Clock When the mains plug is connected to the power supply the clock display will show 12.00 AM (Midnight) indicating the time requires setting. Real time To set the time, press the Time/Alarm off button and either the Fast or Slow button simultaneously. The Fast button is to advance the time display quickly - use it to advance swiftly through several hours, follow up by using the Slow button to set the exact time. The time display will advance each time the button is depressed, or automatically if it is kept depressed. Release the buttons when the correct time is shown. Note: Ensure that the time is correctly set for eitherAMorPM. The PM indicator must be lit for PM operation. If the indicator is not lit the time displayed is AM. Quick on/ The Sleep and Time/Alarm off button can be convenient way to for a short period of Alarm time To display the alarm time, press When you release the button, the display reverts to real Fast and Slow buttons whilst holding down theAlarm button to set the desiredAL1or AL2time. Ensure the correct AM/PM setting is observed. Note: The alarm time can only be set with AL1orAL2position. If the Alarm switch is set toAL1+2, then pressing theAlarm button will only display the real time, not alarm time. Alarm Function Your CR980 has both single or dual alarm functions and operate at one of two preset times or both, as required. For example, you might want one time for during the week and another for the two different times for the same day of the week. Single alarm If you require the alarm to operate once at a given time setting, set the required alarm time as described above and position theAlarm switch to either AL1 or AL2. Set the Function switch to 'Alarm' (for waking to the alarm tone) or 'Auto' (for waking to the radio). The respective LED alarm indicator will now be lit and the alarm/radio will operate at the set time. You could now set the the second alarm function in the same way and simply position the Alarm switch to AL1 on weekdays and AL2 on weekends. Note: Once the AL1 or AL2 has operated, press the Time/Alarm off button once, the alarm/radio will sound again the next day unless the Function switch is set to ' Off' . 5 Dual alarm If you require the position the Alarm 'AL1' and set the required move the Alarm switch 'AL2' and set the second When both alarms have 'AL1+2' . Ensure that the Function 'Alarm' position. The display alarm indicators will both be programmed time. Once the'AL1' has operated, press theTime/Alarm off button once. The alarm/radio will switch off and will operate 'AL2' time. Press the Time/Alarm off button again to cancel. AL1and AL2 will sound again the next day unless the function 'Off' . Wake to alarm Once the alarm time is set, move the Alarm switch to the 'AL1' , 'AL2' or 'AL1+AL2' position. Set theFunction switch to ' Alarm' . TheAL1or AL2 indicator (or both, if dual alarm has been chosen) will light tone(s) will then sound at the preset time. To turn off the alarm immediately, either press theTime/Alarm offbutton, in which case the alarm will operate again 24 hours later, or slide Function switch to 'Off' position to switch off the alarm function. Note: The'AL1' and'AL2' buzzer tones are different for easy recognition. Wake to radio Set the Alarm switch to the 'AL1' , 'AL2' or 'AL1+AL2' position. Set the Function switch to'Auto' . TheAL1orAL2indicator (or both, if dual alarm has been chosen) will light and the radio will then operate at the preset time. Note: Ensure that theVolumecontrol is set at an adequate level to wake you up. If not man...