Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
Alarm 1 indicator 3. Auto dimmer 4. Clock display 5. PM indicator 6. LED Dial pointer 7. Stereo indicator 8. Alarm 2 function switch 9. Alarm 1 function switch 10. Tuning control 11. Volume control (Right hand end) 10 11 2 Controls 14 15 (Top) (Rear) 12. Off button 13. Sleep button 14. Radio On button 15. Snooze button 16. Waveband selector 17. Alarm set button 18. Slow forward button 19. Fast forward button 20. Fast reverse button 21. Slow reverse button 22. Time set button 21 23 23. Battery compartment (on underside) 12 13 16 17 19 18 20 22 3 General Do not allow this unit where excessive heat It is recommended that FM band be used wherever freedom from interference will Mains supply The CR960 will operate from a supply only. For your convenience this product is supplied with a plug which with a fuse of the appropriate rating. If the your socket outlet, it should be removed by unscrewing terminal screws, and removing the cable. The correct style of plug to suit your household together rated fuse should be fitted. IF IN DOUBT - CONSULT A QUALIFIED ELECTRICIAN IMPORTANT. DO NOT make any connection to the larger terminal which is marked with the letter E or by the safety earth symbol or coloured Green or Green-and-yellow. The wires in the mains lead are coloured in accordance with the following codes : BLUE - NEUTRAL BROWN - LIVE As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire coloured BLUE must be connected to the terminal marked N or coloured BLACK. The wire coloured BROWN must be connected to the terminal marked L or coloured RED. If you need any further advice, please call our Technical Helpline on 0181 758 0338 (Mon-Fri) Fuse This apparatus must (BS1363). If another type plug, adaptor or distribution IF IN DOUBT - CONSULT A Back-up Battery Slide the battery cover catch (23) in battery cover. Fit a 9 volt IEC size 6F22 battery into the compartment. Replace the battery settings will be retained during a temporary failure The LED display will not be operational. The battery the unit to function. Setting the time Press and hold down the time set button (22). Use the time (18-21) to adjust the time to the required setting: (18) S.FWD Clock time slow forward. (19) F.FWD Clock time fast forward. (20) F.REV Clock time fast reverse. (21) S.REV Clock time slow reverse. Release the time adjust button followed by the time set button when the required time is reached. Note: The clock uses a 12 hour display with a PM indicator (5). Ensure that the correct 12 hour cycle is selected. Alarms The CR960 has two alarms which can be set and activated independently. Each alarm can be set to the HWS (Humane Wake System) buzzer or radio alarm. e.g. Alarm 1 could be set to HWS buzzer for 8:00 AM, Alarm 2 set to Radio for 8:30 AM. 4 Setting alarm Set the alarm 1 function 1 indicator (2) will show button (17). Use the time (18-21) to adjust the time required setting: (18) S.FWD Alarm time slow forward. (19) F.FWD Alarm time fast forward. (20) F.REV Alarm time fast reverse. (21) S.REV Alarm time slow reverse. Release the time adjust button followed by the required alarm time is reached. Setting alarm time 2 Set the alarm 2 function switch (8) to the HWS or Radio 2 indicator (1) will show in the display. Press and hold down button (17). Use the time adjust buttons (18-21) to adjust the time to the required setting: (18) S.FWD Alarm time slow forward. (19) F.FWD Alarm time fast forward. (20) F.REV Alarm time fast reverse. (21) S.REV Alarm time slow reverse. Release the time adjust button followed by the alarm set button when the required alarm time is reached. Aerials The wire aerial located on the rear of the CR960 is for FM reception. The wire should be fully extended and positioned for optimum reception There is a built in ferrite aerial for MW stations. Rotate the CR960 to the position giving best reception. Radio Operation (FM Stereo) Press the radio on button (14) to turn on the radio. The LED dial pointer (6) located in the tuning scale will light. Set the waveband selector (16) to the "FM Stereo position". Adjust the volume control (11) until a hissing sound is heard. Rotate If the station being illuminate. Adjust the If the FM signal becomes background hiss, you may selector (16) to the "FM" position. button (12). Radio Operation (MW) Press the radio on button (14) to turn on the radio. The LED located in the tuning scale will light. Set the waveband selector (16) to "MW" position. Adjust the volume control (11) heard. Rotate the tuning control (10) until the desired Adjust the volume control (11) to the required sound radio, press the Off button (12). Wake Up to HWS Buzzer The HWS (Humane Wake System) alarm is a buzzer which starts and gradually increases in volume. Set the alarm time as previously described. Set the alarm 1 (9) or alarm (8) function selector to the HWS position. The corresponding alarm 1 (2) or alarm 2 (1) indicator will l...