Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
To use both sleep timer and alarm You can fall asleep to the radio and also be awakened by the radio or buzzer alarm at the preset time. 1 Set the alarm. (See “Setting the alarm”.) 2 Set the sleep timer. (See “Setting the sleep timer”.) Troubleshooting Should any problem occur with the unit, make the following simple checks to determine whether or not servicing is required. If the problem persists, consult your nearest Sony dealer. The clock flashes “AM 12:00” or “0:00” due to a power interruption. • The battery is low. Replace the battery. Remove the old battery and install a new one. The radio or buzzer alarm does not sound at the preset alarm time. • Has the desired radio or buzzer alarm been activated? (i.e., Does the ALARM indicator light up?) The radio alarm is activated but no sound comes on at the preset alarm time. • Has VOLUME been adjusted? Precautions • Operate the unit on the power source specified in “Specifications”. • The nameplate indicating operating voltage, etc. is located on the bottom of the unit. • To disconnect the power cord (mains lead), pull it out by the plug, not the cord. • The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. • Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on a surface (a rug, blanket, etc.) or near materials (a curtain) that might block the ventilation holes. • Should any solid object or liquid fall into the unit, unplug the unit and have it checked by a qualified personnel before operating it any further. • To clean the casing, use a soft cloth dampened with a mild detergent solution. • Do not connect the antenna lead to the external antenna. • To reduce the risk of fire, do not cover the ventilation of the apparatus with newspapers, tablecloths, curtains, etc. And do not place lighted candles on the apparatus. If you have any questions or problems concerning your unit, please consult your nearest Sony dealer. Specifications Time display Model for Central America and Mexico: 12-hour System Model for other countries/ regions: 24-hour system Frequency range Band Frequency FM 87.5 – 108 MHz AM 530 – 1 710 kHz Speaker Approx. 6.6 cm (2 5/8 inches) dia., 8 . Power output 150 mW (at 10% harmonic distortion) Power requirements Model for Central America and Mexico: 120 V AC, 60 Hz Model for Thailand: 230 V AC, 50 Hz Model for other countries/ regions: 230 – 240 V AC, 50 Hz For power backup: 3 V DC, one CR2032 battery Dimensions Approx. 155 . 64.5 . 150 mm (w/h/d) (6 1/8 . 2 5/8 . 6 inches) incl. projecting parts and controls Mass Model for Central America and Mexico: approx. 462.2g (1 lb 0.3 oz) incl. CR2032 battery Model for other countries/regions: approx. 470.2g (1 lb 0.6 oz) incl. CR2032 battery Design and specifications are subject to change without notice. English WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire or electric shock, do not place objects filled with liquids, such as vases, on the apparatus. Connect the apparatus to an easily accessible AC outlet. Should you notice an abnormality in the apparatus, disconnect the main plug from the AC outlet immediately. WARNING Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire. Features • Single alarm FM/AM Clock radio. • Various types of alarms — radio and buzzer. • DST button to adjust Daylight Saving Time/ Summer time. • Date button to display month, day and year. • Battery backup to keep the clock during a power interruption with a CR2032 battery supplied. • Extendable snooze — snooze time can be extended from 10 to 60 minutes in maximum every time you use. About the backup battery To keep good time, as backup power source, this unit needs one CR2032 battery (supplied), in addition to the house current. The battery keeps the clock in the event of a power interruption. Knowing when to replace the battery When the battery becomes weak, “E” indicator appears in the display. In the event of a power interruption when the battery is weak, current time and alarm functions will be initialized. Installing and replacing the battery 1 Keep the AC plug connected to the AC outlet, remove the screw that secures the battery compartment at the bottom of the unit using a screwdriver, and remove the battery compartment. (See Fig. A-1) 2 Insert a new battery in the battery compartment with the e side facing up. To remove the battery from the battery compartment, push it out from the side marked PUSH. (See Fig. A-2) 3 Insert the battery compartment back into the unit and secure it with the screw. (See Fig. A-3) 4 When you are replacing the battery, press RADIO ON to turn “E” indicator off in...