Votes - 2, Average rating: 3.5 ( )

Manafacture: Emerson File size: 100.83 kb File name: Language of manual:

A number of factors, such as, the length of time between the date the radio was manufactured and the date you plugged it in for the first time determine the amount of time before replacement. During this initial storage period, the lithium battery is supplying power to the SmartSet® computer memory. Once you plug the radio in, your household outlet supplies the power, and the battery is not being used. A fresh lithium battery can supply power to the SmartSet® computer for at least 3 years even if it is never connected to an AC power supply. If your radio was connected to your AC supply within a few months after it was manufactured, and you experience only the normal, nuisance type, short duration power interruptions, your battery may last for up to 5 years or even longer. When the battery power drops below a certain level, the “BATT. LOW” indicator will come on. When you see this indicator, you should change the battery as soon as it is convenient for you to do so. To change the battery proceed as follows: 1. Purchase a replacement 3V lithium battery wherever batteries are sold. The battery type is CR2430 or equivalent. 10 2. Remove the battery from its package so it is ready to install. 3. Important: Leave the radio power cord connected to your AC outlet. This will provide power to the SmartSet® computer memory while the original lithium battery is removed. 4. Remove the battery door by pressing down on the arrow mark and slide the door in the direction of the arrows. 5. Use a small screwdriver to remove the two small screws securing the battery cap. BE CAREFUL NOT TO LOSE THESE SMALL SCREWS! 6. Remove the battery cap. Then remove the original battery from the holder and STEP 5 insert the new battery into the holder the same way. 7. Replace the battery cap. Turn the two screws clockwise that secure the battery cap, and confirm that the ‘BATT. LOW’ indicator is ‘Off’. 8. Replace the battery door. 9. Save these instructions. You’ll have to do this again five to eight years from now! BATTERY STEP 6 + RESETTING THE CLOCK AFTER A TOTAL MEMORY LOSS If you do not change the built in lithium battery within a reasonable period of time after you see the low battery warning indicator, the lithium battery may become exhausted and will no longer be able to supply back up power to the SmartSet® internal computer. If the unit is disconnected from the AC outlet after the battery is exhausted, or if a power interruption occurs, the SmartSet® memory will be lost and the clock will need to be reset when the power is restored. Be sure to install a fresh lithium battery before you reset the clock, otherwise the clock will need to be reset each time the power is interrupted. 11 If the lithium battery is exhausted and you experience an interruption in the AC power supply, the clock will reset itself to its initial default setting when the power is restored. The initial default setting is 6:00 AM, Thursday, January 1st (1. 1), 1998. If you notice that the time on your SmartSet® clock radio is completely incorrect, and the month/date and day indicators are also wrong, press the Time and Date buttons together to see the year. If the year display is showing “1998” you probably experienced a total memory loss. To reset the clock after a total memory loss, proceed as follows: 1. Follow the instructions on page 10 and install a new CR2430 lithium battery in the battery compartment. 2. Connect the radio to your AC outlet and let the clock set itself. 3. Depress the Time and Date buttons together. The small display will change from ‘month/date’ to ‘year’. 4. While holding the Time and Date buttons, press the Up (or Down) button to set the small display to the correct year, then release the buttons. 5. Depress the Date button and the Up (or Down) button to set the small display to the correct month and date. The Day indicator will change automatically as you adjust the month/date settings. When the correct month and date appear on the display, release the buttons. 6. Depress the Time button and the Up (or Down) button to set the main display to the correct time. Be sure to confirm that you have set the time correctly to ‘AM’ or ‘PM’ by observing the AM indicator. 7. After you set the time, reconfirm that the Day and Month/Date displays are still correct. Make final adjustments if necessary. SmartSet® clock memory is now reset and the new lithium battery will maintain it for the next 5 to 8 years, depending on the number and duration of the power outages you experience. IMPORTANT NOTE: After resetting the clock, don’t forget to reset your wake up times, and alarm mode settings, and sleep timer settings as well. 12 CARE AND MAINTENANCE If the cabinet becomes dusty, wipe it with a soft cloth. If the cabinet becomes smudged or dirty, clean it with a soft, slightly dampened cloth. Never allow water or any liquid to get inside the cabinet. Never use any abrasive cleaners or cleaning pads as these will damage the finish of your radio. FOR ADDITI...

Download now

Please, enter two numbers from picture: