Votes - 3, Average rating: 4
(
)
)
|
manual abstract
IMPORTANT: After you reset the time, be sure to reset your alarm settings as well. 1. POWER ON/OFF BUTTON 2. VOLUME CONTROL 3. CLOCK SETTING UP BUTTON 4. CLOCK SETTING DOWN BUTTON 5. ALARM1 BUTTON 6. ALARM2 BUTTON 7. SNOOZE BUTTON 8. (AM/FM)BAND / CLOCK SET BUTTON 9. TUNNING CONTROL 10. TIME ZONE SELECTOR 11. DAYLIGHT SAVING TIME SWITCH 12. DIMMER CONTROL 13. AUX IN JACK 14. AUX/RADIO SELECTOR 15. BATTERY COMPARMENT 6 15 14 10 11 12 2 4 3 5 6 9 13 1 7 8 7 1. ALARM 1 INDICATOR 2. ALARM 2 INDICATOR 3. MULTI FUNCTION DISPLAY 4. AM CLOCK INDICATOR 5. PM CLOCK INDICATIOR 6. SPEAKER 2 1 3 4 5 6 AUTO TIME SET This unit features an Automatic Time Set system powered by 2 X “AA” batteries (3V DC) (Included), so you do not need to set the clock time when first plugged in. After the unit is plugged in, the LED display will show the current time automatically after you set the time zone and daylight saving time for desired area. SETTING THE TIME ZONE Change to your time zone area by sliding the TIME ZONE switch on the back of the unit to the appropriate time zone you live in. The default time zone is set to Eastern Standard Time (EST). Please refer to the time zone map below when setting the switch position on the back. 1. Eastern Standard Time (EST) 2. Central Standard Time (CST) 3. Mountain Standard Time (MST) 4. Pacific Standard Time (PST) DAYLIGHT SAVING TIME Slide the DST (Daylight Saving Time) switch on back of the unit to turn Daylight saving time on/off. The clock comes with DST in the ON position as the default. This setting is correct unless you live in Arizona or parts of Indiana where DST is not observed. IMPOTANT: Do not change this setting unless you live in an area which does not observe the Daylight Saving time change. NOTE: The batteries will become weak after time, so replace the batteries as needed. To avoid re-program the time and alarm settings, we recommend leaving the unit plugged in when changing the batteries. 8 PST MST CST EST SETTING THE CLOCK In case the back-up batteries are accidentally removed. You will need to set the clock manually. If the LED display is blinking 1. In standby mode, press the UP button to increase or press the DOWN button to decrease the minutes setting. 2. Press and hold the UP / DOWN button to fast forward/backward the clock setting. 3. Press the BAND/SET button or waiting 5 seconds to confirm the setting. If the LED display is steady 1. In standby mode, press and hold BAND/SET button for 3 seconds, AM or PM indicator flashes on LED display, 2. Press the UP button to increase or press the DOWN button to decrease the minutes setting. 3. Press and hold the UP / DOWN button to fast forward/backward the clock setting. 4. Press the BAND/SET button again to confirm. NOTE There are AM and PM indicators located in the left-hand corner of the clock display. Be sure to observe the correct AM / PM indicator when setting the alarm to make sure the wake time is set correctly for AM or PM. 1. Switch AUX IN / RADIO selector to select radio mode. 2. Press the ON/OFF button once to turn on the unit, display shows FM or AM frequency for 5 seconds. 3. Press the BAND/SET button once to select AM / FM band. 4. Rotary the TUNING control knob to select your desired radio broadcasting station. Display will return to show current time after tuning control idle for 5 seconds. 5. Adjust VOLUME control to your desired listening level. 9 6. When you have finished listening, press the ON/OFF button once to turn off the unit. TIPS FOR BEST RADIO RECEPTION AM - The AM antenna is built inside the radio. If AM reception is weak, change the position of the unit until the internal antenna picks up the strongest signal. FM - If FM reception is weak, fully extend the wire antenna and vary the position and location of the antenna until you find the strongest signal. ALARM OPERATION SETTING THE WAKE UP TIME This unit has Dual Alarm function. Each ALARM can be set to wake to RADIO or ALARM. To set alarm time: 1. Press and hold ALARM1 or ALARM2 button for 3 seconds to enter the ALARM setting mode, LED shows the default alarm time 12:00 AM and the ALARM1 or ALARM2 indicator flashing on the display. 2. Press UP / DOWN button to adjust minutes of you desired ALARM time. Press and hold the button for fast forward / backward setting the alarm time. 3. Press ALARM1 or ALARM2 button again to confirm the ALARM time setting. 4. Press ALARM1 or ALARM2 repeatedly to select wake to ALARM (bUZ) , RADIO (rAd) or turn off the alarm. CHECKING THE WAKE UP TIMES Whenever you want to check the wake up time, simply press and hold the ALARM 1 or ALARM 2 button for 3 seconds. The display will change from current time to wake up time. Release the ALARM button, it will return to current time after 5 seconds. WAKE TO RADIO 1. To select wake to radio mode, press the ALARM button you want to set repeatedly until display shows “rAd”. 2. Release ALARM button and waiting about 5 seconds to confirm. NOTE: 1. Ensuring a desired radio station...