Votes - 3, Average rating: 5
(
)
)
|
manual abstract
– With your finger held down on 7, the time will increase rapidly and continuously from minutes to hours. Release 7 when you reach the approximate time setting. – Pressing 4 will allow you to adjust the time slowly back minute by minute. 3. Release the 7 or 4 buttons when you have reached the correct setting. 4. Adjust the clock control to the CLOCK position to return to clock time display. – To review your set alarm time, adjust the clock control to the respective SET ALARM 1 or SET ALARM 2 position. 5. To select the alarm mode you wish to be awoken by, set the respective ALARM 1or ALARM 2 switch to RAD or BUZ. – If you have selected the radio mode, make sure you have adjusted the volume loud enough to wake you. ALARM OFF You can switch off the alarm in three ways: Unless you choose to cancel the alarm completely, the ALARM RESET option will be automatically selected after 59 minutes from the time your alarm first goes off. ALARM RESET If you want the alarm mode to be stopped immediately, but also wish to repeat the alarm call at the same time for the following day: • Press ALARM RESET during the alarm call. REPEAT ALARM This will repeat your alarm call at 9 minutes intervals • Press SLEEP OFF/REPEAT ALARM. • Press SLEEP OFF/REPEAT ALARM again during the next call if you wish to repeat the alarm call. • If, however, you do not press SLEEP OFF/REPEAT ALARM again, the alarm will sound for 59 minutes before turning itself off. Your alarm time setting will then automatically enter the ALARM RESET mode to sound at the same time next day. Switching off the alarm completely • Before or during the set alarm goes off, push the ALARM (1 or 2) switch to the OFF position. – The alarm indicator will disappear from the display. SLEEP The clock radio has a built-in timer device called the SLEEP, which enables the radio to be automatically switched off after a set period of time; this allows you to lie back, listen and fall asleep. The maximum sleep time is 59 minutes. SLEEP ON 1. Set the RADIO switch to the OFF position. 2. Set your sleep time by pressing on the SLEEP button. Keep your finger on the button and the display will begin to count down from 59 to 00 minutes. 3. Release the button as soon as the required sleep time is reached. SLEEP OFF You can switch off the radio before the sleep time has elapsed: – To cancel the SLEEP function, press SLEEP OFF/REPEAT ALARM. Notes: – The sleep function does not affect the alarm setting (s). – If during SLEEP you have turned down the volume and you have an alarm set in radio mode, make sure you have adjusted the volume loud enough to wake you up the next day. MAINTENANCE – If you do not intend to use the clock radio for a long time, disconnect the set by removing the plug from the wall outlet. The battery should also be removed to prevent chemical leakage which will damage your set. – To clean your set from fingerprints, dust and dirt, use a clean and soft damp cloth or chamois leather. Do not use cleaning products which contain benzene, thinner etc. as these may harm the housing. CLOCK MEMORY BACKUP – When a power failure occurs, the complete clock radio will be switched off. – As soon as the power supply returns, the numbers on the display will start to flash. This indicates that you must set the correct time on the clock. – To retain the clock time and the set alarm time(s) in the event of a power failure or disconnection, insert a 9 volt battery, type 6F22 (not supplied) into the battery compartment: this will act as a clock memory back up. However, the time will not be illuminated on the clock display. Operation of the alarm (s), WEATHERBAND and FM/AM radio are also excluded. For clarity, the battery back up is used to retain the set clock and alarm time (s) only. As soon as the power supply returns, the display will indicate the correct time. • Before inserting the battery, connect the power plug to the wall outlet. • Insert a battery into the battery compartment. – Replace the battery once a year. It is not possible to say precisely how long the battery will last. The service life depends on how often and for how long the power supply fails. This varies according to country and region. – If a fault occurs, first check the points listed below before taking the set for repair. – If you are unable to remedy a problem by following the hints below, consult your dealer or service center. WARNING: Under no circumstances should you try to repair the set yourself, as this will invalidate the warranty. PROBLEM The alarm does not function – POSSIBLE CAUSE – The alarm is not set • REMEDY • Set the alarm time and the alarm switch to BUZ or RAD. No sound – Volume too low for radio. – Volume not adjusted. • Increase the volume. • Adjust the volume. The SLEEP does not function AM broadcast cannot be received properly – RADIO still in ON position. – Weak radio signal. • Switch RADIO to OFF position. • Rotate the set for better reception and make sure the set is placed on a non-metallic ...
Other models in this manual:Watches - AJ34901798 (212.33 kb)