Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
You may program a track or tracks to play more than once if desired. NOTE: Programming can only be done while the player is in the Stop mode. If a disc is playing press the STOP button to stop playback before performing the programming steps below. 1.) Turn the unit ‘On’, press the CD PLAY/PAUSE button to select CD function and load the desired disc in the player. Wait until the player reads the disc and the display shows the total track number. 2.) Press the CLK.ADJ/PROG. button. The AM/PROG. indicator and the Program Number “0 1” flash in the display, indicating that you can select the first track to be programmed. 3.) Press the or buttons to selec cct tt the first track. The desired track number appears on the display. Example: Track “7”. 4.) Press the CLK.ADJ/PROG. button again. The selected track is entered in Program memory number 01 and the display advances to “0 2”indicating that you can select the next track to be programmed. 5.) Repeat Steps 3 and 4 to program up to 20 tracks in the memory. 15 CKD1100_052107.p65 15 21/5/2007, 10:44 6.) After you have programmed all the desired tracks press the CD PLAY/ PAUSE button to begin programmed playback. The AM/PROG. indicator stops flashing and remains ‘On’. Playback will begin on the first track you programmed and continue until all programmed tracks have been played. As each programmed track starts playing the display will briefly show the track number being played and then return to the correct time. NOTES: • After all programmed tracks have played the player stops but the program remains in the memory. Press the CLK.ADJ/PROG. button and then the CD PLAY/PAUSE button to begin programmed playback again. • To clear the program from the memory after the disc stops, press the CLK.ADJ/PROG. button and then press the STOP button. Opening the CD door, pressing the ALARM OFF/POWER button to shut the unit ‘Off’, or switching to the Radio function also clears the program. 16 CKD1100_052107.p65 16 21/5/2007, 10:44 Adjusting the Wake-up Times This clock radio has two separate wake-up alarms that can be set and used independently. To set or adjust the wake-up times please proceed as follows: 1.) Depress and hold the ALARM SET/ DISPLAY button for at least two seconds until just the Hour digits and the AL1 (Alarm 1) indicator are flashing. 2.) While the AL1 Hour digits are flashing press the to set the display to the correct wake-up hour. Example: 7:00 AM or buttons repeatedly Observe the PM indicator to make sure you have set the wake-up hour correctly. If the PM indicator is ‘On’ the wake-up time displayed is “PM”. If the PM indicator is ‘Off’ the wake-up time displayed is “AM”. 3.) When the correct wake-up hour is flashing press the CLK. ADJ/PROG. button again. The Hour digits stop flashing and the minute digits begin to flash. 4.) While the Minute digits are flashing press the or buttons repeatedly to set the display to the correct wake-up minute. 5.) When the desired Alarm 1 wake-up time is showing on the display, press the CLK. ADJ/PROG. button to store the Alarm 1 wake-up time in the timer memory. The AL2 (Alarm 2) indicator and the Alarm 2 Hour digits begin flashing. NOTE: If you do not need to adjust the Alarm 2 wake up time you may just wait 10 seconds. After 10 seconds the Alarm 2 display stops flashing and the clock returns to the correct time. 17 CKD1100_052107.p65 17 21/5/2007, 10:44 6.) While the Alarm 2 Hour digits are flashing press the or buttons repeatedly to set the display to the correct wake-up hour. Example: 9:00 AM Observe the PM indicator to make sure you have set the wake-up hour correctly. If the PM indicator is ‘On’ the wake-up time displayed is “PM”". If the PM indicator is ‘Off’ the wake-up time displayed is “AM”. 7.) When the correct wake-up hour is flashing press the CLK. ADJ/PROG. button again. The Hour digits stop flashing and the minute digits begin to flash. 8.) While the Minute digits are flashing press the or buttons repeatedly to set the display to the correct wake-up minute. 9.) When the desired Alarm 2 wake-up time is showing on the display, press the CLK. ADJ/PROG. button to store the Alarm 2 wake-up time in the timer memory. The display stops flashing and returns to the correct time. The Alarm 2 indicator disappears. IMPORTANT: After you press the CLK. ADJ/PROG. button you must make your wake-up time adjustments within 10 seconds while the wake-up time display is flashing. After 10 seconds the wake-up time display stops flashing, the display returns to the correct time, and no wake-up time adjustments can be made. If this occurs you must begin with Step 1 above and start the wake- up time adjustment process again. 18 CKD1100_052107.p65 18 21/5/2007, 15:56 Setting The Alarms / Selecting The Wake-up Mode After you have adjusted the wake-up times on one or both alarms you must press the respective ALARM 1 and/or ALARM 2 buttons one, two or three times, to activate the alarms and select the wake-up mode. The color of the AL1 and ...