Votes - 4, Average rating: 3.3 ( )

Manafacture: Graco File size: 641.12 kb File name: PD142728B.pdf Language of manual:

The Nursery Unit uses standard 120 volt AC household current. • To use AC adapters, plug the connector on the cord into the AC adapter jack on the side of the Parent Unit and the back of the Nursery Unit. Then plug adapter into a standard wall outlet. • Use ONLY the Graco adapters included with the unit. Do not use these adapters with other equipment under any circumstances. • If units do not work, check that AC adapters are plugged into working outlets. Using AC Adapters • In case you are experiencing some interference, the channel on the Nursery Unit can be changed by sliding the “ch” button on the side of the unit to either channel A or B ("X" or "Y"). Selecting Channels • The channel on the Parent Unit can be changed by sliding the “ch” button on the side of the unit to either channel A or B ("X" or "Y"). NOTE: Both units must be on the same channel. A B A B 3 Low Battery Indication Low Battery Indication Parent Unit • If operated too long on a low battery, you may also experience a poor signal and the Power LED on the front of the parent unit may change from green to red. • You may either turn off the unit, plug in the A/C adapter. Out of Range Indication • If the Parent Unit begins to lose the signal from the Nursery Unit you may hear static or other noise. Immediately move the Parent Unit closer to the Nursery Unit to regain connection. ***Note: It is not uncommon for the Parent Unit to occasionally lose and regain connection with the Nursery Unit in environments that have a significant amount of obstructions. Setting Up the Baby Monitor 1. For optimum operation, it is best to use new batteries in the Parent Unit. 2. Place the Nursery Unit within 10 feet (3 meters) of your baby. Plug an AC adapter into the jack on the side of the Nursery Unit. Plug it into a working 120 volt AC outlet. 3. Aim the Nursery Unit toward your baby. Check that there are no walls or large objects that could block sound transmission. 4. Set both the Nursery Unit and Parent Unit to the same channel, “A” or “B” (“X” or “Y”). 5. Turn on the Nursery Unit using the On/Off switch on the side. The green power light should come on. 6. Place the Parent Unit within five (5) feet (1.5 meters) of the Nursery Unit and turn on the Parent Unit using the On/Off switch on the side of the unit. The green power light should come on. 7. If you have 2 Parent Units, repeat same set-up procedure for 2nd Parent Unit if not continue to Step 8. 8. Your monitor is now ready for use. 4 It is VERY IMPORTANT to test the system when first set up, and at regular times thereafter. Test the units if you suspect they may have been damaged or have not been used for a long time. 1. If two adults are present, have one take the Parent Units to different locations, trying various volume settings, while the other speaks into the Nursery Unit. 2. If only one adult is available, place a ticking clock, radio, or other sound-producing device near the Nursery Unit to test it. 3. When testing, keep the level of your child’s sounds in mind, and adjust the volume accordingly. 4. If there is sound interference, switch the Nursery Unit and the Parent Units to the other channel setting. Testing the System Operation To Listen To Baby • Turn on Nursery Unit using the ON/OFF switch. • Turn on Parent Unit using the Power/Volume wheel. • Adjust the volume on the Parent Unit by turning the Power/Volume wheel. • The Sound Lights on the Parent Unit will illuminate as your child (or other objects) make noise near the Nursery Unit. Please note that the Sound Lights and volume control on the Parent Unit are independent of each other. With the volume turned all the way down, the Sound Lights will still illuminate as your child (or other objects) make noise near the Nursery Unit. • To turn on the Vibration Alert Feature, set the switch on the side of the parent unit to ON. Vibration Alert Feature •To turn on NightLight slide button on side of Nursery Unit up. NightLight Feature 5 TroubleShooting TroubleShooting DO NOT ATTEMPT to modify the unit. Any modifications to the transmitter and/or receiver can void the operator’s authority to operate the equipment. Most problems have a simple Static solution. First, check that: • Interference from other electrical • Power is turned ON for both units equipment — eliminate cause of static (TVs, mixers, computers, fans, fluorescent • Both units are plugged in (or batteries are lights, light dimmers, etc.) fresh in Parent Unit) • Parent Unit too far from Nursery Unit — • Electrical outlet works move them closer. • Volume is turned up on Parent Unit • Significant amount of obstructions • Parent Unit is in range of the Nursery Unit between Parent Unit and Nursery Unit such as walls, ceilings & buildings. Try moving No Sound the Nursery Unit to another part of the • Battery dead or weak — replace or use AC room. adapter. • Change channel on Nursery Unit. • AC adapter not properly connected — Shrill Sound (Feedback) check the connections. • Nursery Unit a...

Download now

Please, enter two numbers from picture: