Manafacture: Philips
File size: 675.53 kb
File name:
|
manual abstract
Do not attempt to repair or modify this equipment Any repairs or alterations made by the user to the equipment may void the warranty and compliance of the equipment. Refer ser vicing to authorized or designated ser vice centers. general description (Fig. 1) A Baby unit 1 On/off button 3 2 ON light 3 Volume +/– buttons 4 Batter y check light T 5 Nightlight 6 Nightlight button Q 7 PAGE button 8 Microphone 9 Adapter EngliSh 10 Small plug 11 Batter y compar tment lid 12 Inlet for small plug 13 Batter y compar tment B Parent unit (2 pieces, only one is shown) 1 TALK button 2 LINK light 3 SENSITIVITY button 4 On/off button 3 5 Opening for belt clip and neck strap 6 Sound level lights 7 Volume +/– buttons 8 Batter y check light T 9 Microphone 10 Loudspeaker 11 Batter y compar tment 12 Belt clip 13 Batter y compar tment lid 14 Neck strap 15 Adapter 16 Charger 17 POWER light C Travel pouch Preparing for use Baby unit You can operate the baby unit directly from the power supply or on batteries. Even if you are going to operate the unit from the power supply, we advise you to inser t batteries.This guarantees automatic back-up in case of power failure. Corded operation 1 Put the small plug in the baby unit and put the adapter in a wall outlet (Fig. ). Battery operation The baby unit runs on four 1.5V R6 AA batteries (not included). We strongly advise you to use Philips LR6 PowerLife batteries. Make sure your hands and the unit are dry when you insert the batteries. Turn the battery compartment lid to the left ( A OPEN) with the palm of your hand. (Fig. ) Remove the lid. Insert four 1.5V R6 AA batteries (Fig. ). 1 Place two batteries on top of each other and make sure the + and – poles of the batteries , point in the right direction. Put the battery compartment lid back onto the unit and turn it to the right (CLOSE .) withthe palm of your hand to close it. (Fig. 5) Note: When the batteries are running low, the battery check light ( T) lights up red. Parent unit This appliance comes with two parent units and two chargers instead of one, so that your baby can be monitored by two persons at the same time. 10 EngliSh Battery operation The parent unit runs on two rechargeable 1.2V AAA NiMH batteries that are supplied with the appliance. Make sure your hands and the unit are dry when you insert the batteries. Slide the battery compartment lid downwards to remove it (Fig. 6). Insert the two rechargeable batteries (Fig. ). Make sure the + and – poles of the batteries point in the right direction. , 1 Slide the battery compartment lid back onto the back of the parent unit until it locks into position (‘click’) (Fig. ). Put the adapter in a wall outlet and place the parent unit in the charger (Fig. ). The POWER light on the charger lights up. ,5 Leave the parent unit in the charger until the batteries are fully charged When charging for the first time or after a long period of disuse: turn off the , parent unit and let it charge continuously for at least 10 hours. Charging normally takes hours, but it takes longer when the parent unit is turned on while , charging.To keep the charging time as short as possible, turn off the parent unit during charging. The POWER light on the charger stays on, even when the batteries are fully charged. , When the batteries are fully charged, the parent unit can be used cordlessly for at least , hours. Note:The operating time of 24 hours is based on the assumption that the baby unit transmits 25% of the time and is in standby mode for the rest of the time (when the baby does not make any sound). Note:When the parent unit batteries are charged for the first time, the operating time is less than 24 hours.The batteries only reach their full capacity after you have charged and discharged them four times. Note:When the batteries are running low, the battery check light ( T) flashes red. Place the parent unit in the charger. Note:When the parent unit is not in the charger, the batteries gradually discharge, even when the parent unit is turned off. Corded operation 1 Make sure you have inserted the rechargeable batteries in the parent unit Put the adapter of the charger in the wall outlet and place the parent unit in the charger (Fig. ). The POWER light on the charger lights up. , Using the appliance Place the parent unit and the baby unit in the same room to test the connection (Fig. 10). Make sure the baby unit is at least 1 meter/3 feet away from the parent unit. Press and hold the on/off button 3 on the baby unit for seconds. (Fig. 11) The nightlight lights up briefly. , The ON light lights up. , Press and hold the on/off button 3 on the parent unit for seconds. (Fig. 1 ) The sound level lights light up blue briefly. , The battery check light ( T) lights up red briefly. , EngliSh 11 The LINK light flashes red briefly and then starts to flash green while the parent unit tries to , establish connection with the baby unit. The LINK light on the parent unit flashes green until connection has been establi...