Votes - 0, Average rating: 0 ( )

Manafacture: Philips File size: 1.87 mb File name: Language of manual:

2 Connect the AC power adapter (A-4) to a wall outlet. . The baby unit is now ready for mains operated use. Battery operated use 1 Remove the battery compartment cover (A-10) of the baby unit, using a coin. Getting your baby monitor ready EN 2 Insert four 1,5V AA batteries, noting the + and – configuration inside the battery compartment (batteries are not supplied, we recommend Philips Alkaline batteries). 3 Close the battery compartment cover (A-10), using a coin. . The baby unit is now ready for battery operated use. Parent unit A rechargeable battery pack has already been installed in the parent unit. 1 Connect the power adapter cord to the power supply jack (DC 9V — ——< <<+ ++ - B-7) of the charging base (B-5). 2 Connect the AC power adapter (B-3) to a wall outlet. 3 Place the parent unit in the charging base (B-5). > The charging light (B-6) lights up red. 4 Leave the parent unit in the charging base (B-5) until the batteries are fully charged (at least 14 hours). > When the batteries are fully charged, the charging light (B-6) will gradually dim.The parent unit can now be taken out of the charging base and used cordlessly for up to 10 hours. > When the POWER light (B-10) flashes red, battery power is low. Place the parent unit in the charging base (B-5) to recharge the batteries. . The parent unit is now ready for use! EN Using your baby monitor 1 Position both units in the same room to test the connection. Make sure the baby unit is at least 1 meter / 3 feet away from the parent unit. 2 Press the ON/OFF button (A-1) to switch on the baby unit. > The POWER light (A-7) lights up green. 3 Switch on the parent unit using the ON/OFF switch (B-9) and adjust the volume to the level you prefer using the VOLUME control (B-9). > The POWER light (B-10) lights up green. > When connection has been established between the units, the LINK light (B-8) on the parent unit lights up green. 4 Position the baby unit at least 1 meter / 3 feet away from your baby. 5 Position the parent unit at the desired place within the operating range of the baby unit but at least 1 meter / 3 feet away from the baby unit. For more information on the operating range see ‘Technical specifications’. . Your can now monitor you baby! Features EN Avoiding interference (channel selection) Always make sure that the CHANNEL selection switches (A-9, B-11) inside the battery compartments on both units are set to the same position! With the CHANNEL selection switches (A-9, B-11) you can select sixteen different channel positions. If you experience interference from other baby monitors, radio devices, etc. select a different channel. 1 Open the battery compartment covers (A-10, B-12) of both units. • Parent unit: slide down the cover (B-12). • Baby unit: use a coin. 2 Lift up the rechargeable battery pack (B-14) of the parent unit. If you are operating the baby unit on battery power, remove the batteries from the unit. 3 Use a small, flat screwdriver to rotate the inner circle of the channel selection switches (A-9, B-11) to the desired position. Make sure both units are set to the same channel. 4 Put batteries and battery pack back in place. 5 Close the battery compartment covers (A-10, B-12). EN Features Adjusting microphone sensitivity With the microphone sensitivity switch (A-8) on the baby unit, you can set the sound, coming from the baby unit, to the desired level: low, mid or high. When set to the maximum level, the baby unit monitors almost all sounds.You can only change the microphone sensitivity if the connection between the baby unit and the parent unit is established (when the LINK light (B-8) lights continuously green). • Use the microphone sensitivity switch (A-8) to adjust the baby unit microphone sensitivity to the desired level. You can use your own voice as a sound reference. > The POWER light (A-7) on the baby unit lights up yellow when a sound is picked up. Monitoring baby silently • Use the ON/OFF switch / VOLUME control (B-9) on the parent unit to set the volume to the lowest level. Do not switch off the parent unit completely! > The sound level lights (B-1) on the parent unit visually alert you to baby’s sounds. The more sounds your baby makes, the more lights you will see. > When no sound is detected all sound level lights (B-1) will be off. Switching the night-light on and off 1 Press the baby unit night light (A-2) to switch it on and off. Features EN Switching the LINK alarm on and off You can switch on the LINK alarm on the parent unit. The LINK alarm will beep when connection between the units is lost. 1 Open the parent unit’s battery compartment (B-12) by sliding down the cover. 2 Set the switch (B-13) inside the compartment to the ON ( ) position. 3 Slide the battery compartment cover (B-12) back in place until it clicks in position. • To switch off the alarm, set the switch (B-13) to the OFF ( ) position. Connecting / disconnecting the belt clip If the parent unit is operating on batteries, you can carry it in and aro...

Download now

Please, enter two numbers from picture: