Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
3.2 Accessories A wide range of accessories are available for the SP200/210. The list below represents a summary of accessories available at the time this manual was published. For up-to-date listings, and for price and availability, please refer to the current Price Book. Order Code Description Batteries QPA-1350 1350mAh NimH battery. Chargers QPA-1185-2 2-pin (European) Intelligent fast charger with mains adapter QPA-1185-3 3-pin (UK) Intelligent fast charger with mains adapter QPA-1185 Spare cup for the above chargers (No PSU) QPA-1195-2 6 + 6 Intelligent fast charger (Euro) QPA-1195-3 6 + 6 Intelligent fast charger (UK) CA1246 In-car charger Speaker / Microphone accessories MA100-01 Small Remote speaker mic. MA100-02 Standard Remote speaker mic. Headset Accessories HS100-02 Lightweight headset QPA1432 Lightweight headset QPA1433 Two-way covert kit QPA1455 Earbud HS100-01 Earbud with Earhanger Cases CA1487 Lightweight Nylon case. CA1475 Soft Leather case CA1476 Soft Leather case with window CA-7059 Belt Clip Programmer SMP6100 SP200/210 Programming Kit 3.3 Options None Issue 1.0 ACCESSORIES & OPTIONS 03/01 Page 3-1 Maxon SP200/210 Radio SP200/210 ACCESSORIES & OPTIONS Issue 1.0 Page 3-2 03/01 SP200/210 Maxon SP200/210 Radio Issue 1.0 INSTALLATION, COMMISSIONING & ALIGNMENT 03/01 Page 4-1 4 INSTALLATION, COMMISSIONING & ALIGNMENT 4.1 Installation The SP200/210 is a hand-held radio and thus requires no installation. The User should ensure that the batteries are charged before commencing commissioning tests. 4.2 Connections 1. Antenna connector: socket. 2. Channel Busy / Talk tri-colour LED. 3. Display 4. Main Power switch and volume control. Fully anti-clockwise is the OFF position. 5. Battery Release Catch. 6. Speaker. 7. Push To Talk (PTT) button. 8. Microphone. 9. Scan button. 10. Monitor button (unmutes the radio). 11. Channel select keys: Up / Down keys, used to select channels. 12. Accessories socket (microphone & speaker) Note: Socket 12 is the Accessories Connector, which may be used to connect the radio to the following: An optional remote speaker / microphone An optional headset A PC for programming using SMP6100software 4 2 1 12 6 7 8 9 10 11 5 BACK 3 Figure 4-1 - Connections and controls Maxon SP200/210 Radio SP200/210 The Accessory connector is wired as follows: PTT / Mic Ground Speaker Figure 4-2 – Connections The small multi-pin connector, which is connected to the other end of the test lead, is wired as follows: 1 2 3 4 5 6 rear of View from connector Screen PTT / Mic Speaker Figure 4-3 - Hirose connector 4.3 Commissioning This section covers the tests, which should be undertaken prior to handover of the radio to the end user. All of the following tests can be carried out without having to gain access to the interior of the radio. Recommended Test Equipment The alignment and performance test procedures assume the use of the following equipment. The functions of most of the equipment may be found in a “Communications Test Set”. This type of equipment is available from a number of test equipment manufacturers. Throughout this book reference will be made to the use of the Communications Test Set. Where applicable, the equivalent discrete item of test equipment may be used. COMMUNICATION TEST SET DC POWER SUPPLY RADIO VOLT METER OSCILLOSCOPE DEMOD AF IN AF OUT . . RF TEST BOX S2055K Figure 4-4 – Commissioning Test Setup using SK2055 Service Kit INSTALLATION, COMMISSIONING & ALIGNMENT -Issue 1.0 Page 4-2 03/01 SP200/210 Maxon SP200/210 Radio Commissioning Equipment 1 3 45 2 Figure 4-5 – Commissioning Kit Note: For those dealers who already have the SK2055 Service Kit (SL25/55) the audio cable (2), CA8700, may be purchased. This interfaces the Service Kit to the SP200/210 and allows all simple, commissioning audio measurements to be made. SMA adapter (5), ME210089 will also be required. Flexi-pcb (3), ME110016 may be required if simple internal adjustments are to be made. Note: The equipment shown in Figure 4-5 allows only VCO and power adjustments to be made to the SP200/210. The full Service Kit, SK3100, is required for setting deviation. Please refer to Figure 4-6 for the set-up using discrete test equipment and Figure 4-4 for the set-up using the Communications Test Set. If the ACC-2003 Interface Box is used, please refer to Figure 4-7. Issue 1.0 INSTALLATION, COMMISSIONING & ALIGNMENT 03/01 Page 4-3 Maxon SP200/210 Radio SP200/210 Discrete Test Equipment RF Signal Generator (with CTCSS/1kHz tone) RF Power Meter RF Frequency Counter Spectrum Analyser and notch filter (optional) Audio Signal Generator Audio Power Meter SINAD Meter Modulation Meter Oscilloscope Voltmeter DC Power Supply, 0 - 10V 3A min. RF SIGNAL GENERATOR AUDIO POWER METER VOLT METER 154.625WATT METER WITH 20dB ATTENUATOR AUDIO MODULATION- METER AUDIO GENERATOR DC POWER SUPPLY RADIO OSCILLOSCOPE SPECTRUM ANALYZER (optional) SINAD METER DISTORTION METER TEST BOX 2055 SK Combined Equipment Communications Test Set (e.g. Marconi T...
Other models in this manual:Two-Way Radio - SP210 (2.86 mb)
Two-Way Radio - SP200 (2.86 mb)
Two-Way Radio - SP210 (2.86 mb)
Two-Way Radio - SP200 (2.86 mb)