............................................3-8 Accessory Tool Usage. ...................................... 3-10 MAINTENANCE Periodic Maintenance...........................................4-1 Daily/ Regular Maintenance.................................4-2 Vacuum Motor Replacement ...............................4-3 Belt Replacement.................................................4-4 Solution Pump Replacement................................4-5 Wiring Diagram. ......................................

Take care not to run over loose objects oredges of area rugs. Stallingbrush may result in premature belt failure. Tip: make only one trip to the sink by removing the entire portable cleaner. fill and empty in the same trip. 4. 2. 3. WARNING: to reduce the risk of fire, electric shock, or injury, turn power off and disconnect plug from electrical outlet before performing maintenance or troubleshooting. Tip: for best results empty, rinse and dry both tanks before storing. 800.237.7691 9 Operations

If that is needed, please follow the instructions below. 1. turn off the machine, and unplug it from the outlet. Remove portable spot cleaner. 2. Remove the nozzle by unscrewing three WARNING: to reduce the risk of fire, electric shock or injury, unplug from the outletbefore servicing. screws on the nozzle cover. 3. turn the machine on its side. ImPORTANT: with portable spot cleaning pedal facing down. 4. Remove end cap by unscrewing the 3 screws. take care not to drop the screws into the unit.

The portable spot cleaner detaches to clean tough spots and stains and hard to reach areas. Hot water heater This deep cleaner features a patented built-in hot water heater which will heat the hot tap water you put in to safely optimize cleaning effectiveness. The heater temperature is limited to prevent carpet damage. The heater automatically turns on when you turn the machine on. This operates only in upright cleaning mode. Scotchgard™ Protector Carpet protection applied at the mill typically

2. using the brush on the tool, gently scrub the area to be cleaned. 3. apply downward pressure on the tool and pull it toward you. the suction will remove the dirt and cleaning solution. continue until no more dirt can be removed. Adsdfdd ghg bvhcvbbj jkn hnbjgcghh fhl kl Manufacturer’s tag ImPORTANT Check for colorfastness in an inconspicuous place. If possible, check upholstery stuffing. Colored stuffing may bleed through fabric 800.237.7691 11 Operations Portable spot cleaning mode continued

NOTE: When charging, the Spot Lifter and charger may become warm to the touch. This is normal and no cause for concern. 2. Spot Lifter must be in “ O ” (OFF) position to charge. 3. When completely charged, your Spot Lifter will operate for up to 7 minutes for model 1718 and up to 15 minutes for model 1719. When completely discharged, it will take approximately 12 hours to fully recharge. Tip: For maximum battery life, completely discharge and recharge Spot Lifter every 1-2 months. Tip: After uni

Refill if needed. cleaning solution and remove any Never run dry. surface soil. Using the brush before applying solution can push soil more deeply into carpet. Spot cleaning upholstery 1. Check manufacturer’s tag before cleaning. “W” or “WS” on the tag means you can use your Spot Lifter. If tag is coded with an “S” (with diagonal strike-through), or says “Dry Clean Only,” do not proceed. 2. If manufacturer’s tag is missing or not coded, check with your furniture dealer. NOTE: If possible, check

Do not use on velvet or silk. If manufacturer’s tag is missing or not coded, check with your furniture dealer. 2. Check for colourfastness in an inconspicuous place. 3. If possible, check upholstery stuffing. Coloured stuffing may bleed through fabric when wet. 4. Plan activities to give upholstery time to dry. 5. Vacuum thoroughly to pick up loose debris and pet hair. Use a vacuum with a brush attachment and a crevice tool to clean in fabric folds and tufts. 6. To begin cleaning with attachment

7. Remove and rinse hose in clean, running water. let dry completely. 8. empty dirty and clean water tanks and rinse following instructions on page 13. 3A. 3B. 3B. 4. 5. 10 800.237.7691 Operations Operations Cleaning with Oxy Gen2 tool Select models only 1. follow instruction on page 10 to attach hose to machine. 2. To pretreat heavy traffic areas: A. Pour oxy gen2 formula into the oxy gen2 tool and attach tool to your machine’s hose. B. hold tool 2-4 inches above the floor and press red trigger

Leaving it for an extended period of time may cause it to set and become permanent 1. blot up liquids with an absorbent cloth or paper towels. White materials are recommended because certain dyes may bleed and make the stain worse. 2. gently scrape up any semi-solids with a spoon or spatula. do not use a knife or other utensil with sharp edges because it could damage the carpet or upholstery. 3. if the area has dried, remove the remaining semi-solids and residue with a sweeper or vacuum. 4. be s