Votes - 4, Average rating: 4
(
)
)
|
manual abstract
twist the collar to “lock” to lock into place. to retract, twist to unlock, pull toward you and twist to relock. all available items may not be included with your model. other tools are available; to order, please refer to page 19. attENtIoN: always place the vacuum cleaner on the floor in its fully upright position when using tools. placing the vacuum in this position automatically stops the rotating brush. 2 caUtIoN: to avoid personal injury and to prevent the cleaner from falling when cleaning stairs, always place it at the bottom of the stairs. 800.237.7691 8 caUtIoN: Make sure vacuum cleaner has been switched off and unplugged before removing dirt container. Emptying the dirt container Empty the dirt container as soon as the dirt reaches the “full” line on the side of the container. 1. Press the release button on top of the carrying handle to remove the dirt container. 2. Choose an emptying method. Method #2 is recommended for allergy sufferers. Method #1 – hold the dirt container over trash can and push the emptying button to open the bottom (2a). Close the bottom after the dirt empties. Method #2 – place a plastic bag over the bottom of the dirt container. Push the emptying button through the plastic to open the bottom (2b). After the dust settles, close the bottom and remove the bag to discard. 3. Replace dirt container on cleaner by aligning the bottom and pushing back until it snaps into place. Operation1 2a 2b 3 800.237.7691 9 Maintenance and care Cleaning the dirt container additional steps can be taken to clean the dirt container as necessary. 1. Ensure the dirt container has been emptied. 2. Remove the lower portion by pressing the front latch on the upper portion as shown. 3. Clean the screen with a cloth or soft brush to remove dust or debris. 4. If desired, the lower dirt container may be washed in warm water. Make sure it is completely dry before reassembling. Do not put in dishwasher. 5. To reassemble, hold the carry handle and place the upper portion into the lower portion, lining up the front and back latches. Push down until both latches click into place. Make sure the dirt container is securely assembled before replacing it on machine. Cleaning the pre-motor filter the pre-motor filter should be checked monthly and washed as needed to maintain performance. More or less frequent cleaning may be required based on individual vacuuming habits and types of debris picked up . 1. The filter is located in the door labeled "Filter" behind the dirt container. Push the tab at the top and swing the door down to access. 2. Remove foam filter and hold under running water to wash. Mild detergent may also be used if desired. Wring excess water from filter. air dry thoroughly before replacing. WaRNING: to reduce the risk of electric shock, turn power switch off and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks. 2 3 5 WaRNING: Do not operate the cleaner with a damp or wet filter or without all the filters in place. 10 800.237.7691 1Replacing the hEpa filter cartridge Maintenance and care the hEpa filter cartridge should be replaced if machine performance is noticeably declining. More or less frequent replacing may be required based on individual vacuuming habits and types of debris picked up. Note: to have the benefits of the airetight® hEpa System, you must use the bISSEll hEpa filter cartridge. 1. Remove the dirt container. 2. To remove the HEPA filter cartridge, push in on the front of the filter door to unlatch. Lift up to access. 3. To check or remove, unscrew the center 3 screw. 4. If necessary, replace the used HEPA filter cartridge with a new one. Note: to avoid damaging the hEpafilter cartridge and reducing its filtration capabilities, be careful not to touch the filter material. the hEpafilter cartridge is not washable. 5. To ensure a tight seal be sure to tighten the filter cartridge screw until snug. Do Not oVER tIGhtEN. Make sure the filter door latches completely. 11 800.237.7691 Maintenance and care clearing clogs low suction or poor pickup may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action in the dirt container, check for a clog. WaRNING: to reduce the risk of electric shock, turn power switch off and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks. If there is no suction or if suction is reduced at the hose, follow these steps to check for and clear the clog: 1. Turn power switch off. 2. Unplug cleaner from electrical outlet. 3. Check the pre-motor filter and clean as necessary (see cleaning your pre-motor filter on page 10). 4. Check the HEPA filter cartridge and replace if necessary (see replacing the HEPA filter cartridge on page 11). 5. Check to see if dirt container is full. Empty if needed. 6. Remove lower portion of dirt co...