Login:
Votes - 0, Average rating: 0 ( )

User manual Philips, model FC7070/01

Manafacture: Philips
File size: 10.49 mb
File name:
Language of manual:itenfrdenl
Free link for this manual available at the bottom of the page



manual abstract


Open the mopping nozzle lid, remove the mopping brush cover and remove the object. Reinser t the mopping brush cover, close the mopping nozzle lid, put the plug in the wall socket and switch on the appliance again (see chapter ‘Using your AquaTrio’, section ‘Active protection system is activated’). If you find no object, the active protection system may have been activated because the mopping brushes are too wet (see second cause of previous problem) or because you moved the appliance over a carpet. Pull the plug out of the wall socket, open and close the mopping nozzle lid, put the plug in the wall socket again, switch on the appliance and star t cleaning again. I have just filled the clean water tank, but the tank full/tank empty light keeps flashing when I switch on the appliance. The tank full/tank empty light may flash a few times when you switch on the appliance after you have filled the clean water tank. When you switch on the appliance after you have filled the clean water tank, the tank full/tank empty light may flash a few times and the appliance may switch off automatically.This happens because it takes a few seconds for the water to reach the mopping nozzle. Release the power-on button. Then push the unlock slide forwards and press the power-on button to switch on the appliance again (see chapter ‘Preparing for use’, section ‘Filling the clean water tank’). If the tank full/tank empty light continues to flash after filling, the clean water tank may not be assembled properly. Make sure you place the clean water tank properly and that the lever is locked (see chapter ‘Preparing for use’, section ‘Filling the clean water tank’). The mopping nozzle lid is not closed properly.The sound of the appliance decreases and the appliance no longer applies water to the floor because the mopping brushes do not rotate and the appliance does not mop up anything. Make sure the mopping brushes and the mopping brush cover are assembled correctly. Close the mopping nozzle lid properly. Make sure you press the lid until it locks with a click (see chapter ‘Cleaning and maintenance’, section ‘Reassembling the mopping nozzle’). Water drips out Water leaks from Remove the clean water tank from the appliance. Put of the appliance. the clean water tank the cap on the water tank if it was not there or turn the because you have cap clockwise to fasten it (see chapter ‘Preparing for use’, not put the cap on section ‘Filling the clean water tank’). the clean water tank or you have not fastened this cap properly. Problem Possible cause solution Water leaks from the clean water tank because you overfilled the clean water tank. Do not fill the clean water tank beyond the MAX indication. If you do, water may spill from the clean water tank when you fasten the cap (see chapter ‘Preparing for use’, section ‘Filling the clean water tank’). Water leaks from the dir ty water tank because you tilted the upper body too far backwards or because you placed the appliance on its side.This caused wastewater to run out of the dir ty water tank. Do not tilt the upper body of the appliance too far backwards, for instance when you clean under a low table. Do not place the appliance on its side when there is wastewater in the dir ty water tank (see chapter ‘Impor tant’, section ‘Caution’). I cannot remove the mopping brushes. You probably tried to remove them by pulling at the wrong side. grab the lime green grips of the brushes and pull the brushes up a little.Then you should be able to slide them off the projection on the other side (see chapter ‘Cleaning and maintenance’, section ‘Cleaning the mopping nozzle’). E N g LI sh I cannot tilt the appliance backwards without the The appliance is locked in parking position. Press the nozzle with your foot and release the appliance from parking position (see chapter ‘Using your AquaTrio’, section ‘Pausing during use’). nozzle coming off the floor. 27 Problem Possible cause solution The appliance does not take up water when I flush the mopping nozzle. You poured too much water into the flushing tray or you poured it in too fast.This causes the mopping brushes to become too wet. When the brushes are too wet, the active protection system is activated. The mopping brushes stopped rotating because they encountered too heavy resistance. switch off the appliance, put the appliance upright in parking position (‘click’), and pull the plug out of the wall socket. Remove the mopping brushes from the mopping nozzle and remove excess water from the mopping brushes by squeezing them over a sink (see chapter ‘Cleaning and maintenance’, section ‘Cleaning the mopping nozzle’).Then you can reinser t the mopping brushes, reinser t the mopping brush cover, close the mopping nozzle lid and switch on the appliance again (see chapter ‘Cleaning and maintenance’, section ‘Reassembling the mopping nozzle’). If this does not work, let the mopping brushes dr y (see chapter ‘Cleaning and maintenance’, section ‘Cleaning the mopping ...

Other models in this manual:
Vacuum Cleaners - FC7070/11 (10.49 mb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category