Votes - 0, Average rating: 0 ( )

Manafacture: Philips File size: 8.21 mb File name: Language of manual:

10). 5 Lift the motor unit from the container by the handle (Fig. 11). 6 Turn the motor unit upside down (Fig. 12). 7 Remove the diffuser from the motor unit (Fig. 13). 8 Remove the float unit from the container (Fig. 14). 9 Insert a paper dustbag or the reusable dustbag (some countries only). Press and hold the red lever while you place the front of the dustbag into the holder (Fig. 15). 10 First insert the bottom edge (1).Then press the top edge into place (2) (Fig. 16). Note: Make sure that the two projections of the front point downwards and that the centre of the bottom edge rests on the ridge of the holder. English 11 Slide the holder with dustbag into the appliance in such a way that the holder is kept in place by the two ridges in the container (Fig. 17). 12 Put the motor unit back into the container and close the clamps (‘click’). (Fig. 18) 13 Put the micro filter into place (specific types only) (Fig. 19). Note: See chapter ‘Replacement’ for replacing the paper dustbag or chapter ‘Cleaning and maintenance’for emptying the reusable dustbag (some countries only). Preparing for wet use Always remove the paper or reusable dustbag (some countries only) and the micro filter (specific types only) before wet use. Preparing for vacuuming liquids To vacuum liquids, you need the float unit and the diffuser. 1 2 3 4 5 Make sure the appliance is unplugged. Undo the clamps (Fig. 10). Lift the motor unit from the container by the handle (Fig. 11). Remove the reusable dustbag (some countries only) or the paper dustbag (see chapter ‘Replacement’) (Fig. 20). Insert the float unit into the container by its handle (Fig. 21). Note:The float unit only fits into the appliance in one way. 6 7 8 9 Turn the motor unit upside down (Fig. 12). Insert the diffuser into the motor unit (Fig. 22). Put the motor unit back into the container and close the clamps (‘click’) (Fig. 18). Remove the micro filter (specific types only) (Fig. 23). Note: If the micro filter is exposed to excessive air humidity, it loses its electrostatic properties. Now the appliance is ready for vacuuming liquids. Preparing for shampooing To shampoo floors, you need the float unit, the diffuser, the shampoo reser voir (filled with shampoo and water), the double-injection nozzle and the shampoo trigger. 1 2 3 4 5 6 7 8 Follow steps 1 to 9 in ‘Preparing for vacuuming liquids’. Fill the shampoo reservoir with cold water (Fig. 24). Add one measuring cup of cleaning liquid to the full reservoir (Fig. 25). Attach the shampoo reservoir to the appliance (Fig. 26). Insert the short shampoo hose into the connector on the vacuum cleaner (1) and turn it anticlockwise (2) (Fig. 27). Connect the long shampoo hose to the shampoo trigger (Fig. 28). Fasten the shampoo trigger to the handgrip of the suction hose (Fig. 29). Firmly insert the end of the long shampoo hose into the connector on the vacuum cleaner (‘click’) (Fig. 30). -To release the shampoo hose, push the ring towards the appliance (Fig. 31). 10 English Fasten the long shampoo hose to the suction hose and suction tube with the shampoo hose clips (Fig. 32). 10 Attach the double-injection nozzle (Fig. 6). The appliance is now ready for shampooing soft floors, such as carpets and rugs. using the appliance 1 2 Pull the mains cord out of the appliance and insert the mains plug into the wall socket (Fig. 33). Press the motor on/off button to switch on the appliance (Fig. 34). Dry use Convertible nozzle 1 You can use the convertible nozzle to vacuum hard and soft floors: (Fig. 35) -With the brush strip folded out, you can use the nozzle to clean hard floors (wooden, ceramic, stone and synthetic floors) -With the brush strip folded in, you can use the nozzle to clean soft floors (carpets and rugs) Wet use vacuuming liquids Note:When you vacuum water from a place that is located higher than the appliance itself (e.g. a roof gutter or roof water tank), the appliance inevitably functions as a syphon. As a result, the container fills up more quickly than usual and may overflow. Make sure you never exceed the maximum capacity of the container (9 litres/2 gallons) (Fig. 36). To make sure that the container does not overflow when you vacuum liquids, perform the following procedure at regular inter vals: Lift the nozzle out of the water. Press the motor on/off button to switch off the appliance. Remove the mains plug from the wall socket. Empty the container. shampooing carpets Start as far away from the door as possible and then work your way towards the door. Apply shampoo by squeezing the trigger on the handgrip of the tube (Fig. 37). Make overlapping strokes to cover the entire area to be cleaned. 1 2 3 4 1 2 3 Note: If there are still traces of liquid on the area you have just cleaned, pass the vacuum cleaner over this area once more without applying shampoo. 4 After shampooing, release the trigger and switch off the pump. Keep the appliance switched on (Fig. 38). 5 Lift the nozzle off the floor.Then simply let the applian...

Download now

Please, enter two numbers from picture: