Votes - 3, Average rating: 5
(
)
)
|
manual abstract
This is because we test all our steam mops 100% before you buy them, so you get a quality Shark® Steam Mop. -ajjr -a^ o Two-Sided Micro-Fiber Pocket for the Large Area Mop Head Two-Sided Micro-Fiber Pocket for the All-Purpose Mop Head Two-Sided Micro-Fiber Pocket for the Versa-Tile™ Mop Head Carpet Glider Filling Flask Versa-Tile™ Mop Head g All-Purpose Mop Head TECHNICAL SPECIFICATIONS Voltage: 120V., 60Hz. Power: 1550 Watts Water Capacity: 450 ml (15 oz.) h Quick Release Swivel Cord Wrap i Cord Clips I Mop Handle k Telescopic Handle Latch I Water Tank Viewing Window m Power-On Blue Light (Lights up when plugged-in) n Water Tank Cap o Large Area Mop Head TOLL FREE: 1-800-798-7398 Л IMPORTANT: First things first, always make sure the mop is UNPLUGGED from the wall when not in use. Never fill the mop, attach the mop head, change or remove the micro-fiber pocket when the mop is plugged into the wall. If you have hard water you might want to use distilled water to prolong the life of the Shark® Steam Mop. Make sure you only add water to the tank. Chemicals or cleaning solution may damage the appliance and could be unsafe for you and your family. 1 Turn the water tank cap counter clockwise and remove from the tank. Use the filling flask and pour water into the tank. Please don’t overfill. Replace the cap on the water tank by turning clockwise and tightening. A IMPORTANT: Don’t use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with wax or some no wax floors, the sheen may be removed by the heat and steam action. It is always recommended to test an isolated area of the surface to be cleaned before proceeding. We recommend that you check the use and care instructions from the floor manufacturer. 2 Select a mop head. All of the mop heads can be used on your floors, but the Versa-Tile" bathroom head is particularly useful for tight corners and the Large Area mop head is great for big jobs. Use the lavender loop on the side of the micro-fiber cleaning pocket to place around the mop head. Then attach the quick fasteners on the top of the pocket to secure in place. You can also use the loop to pull the dirty pocket off when you are done mopping after it has cooled. 3 Snap the mop head into the base to secure it. Using Your Steam Mop A IMPORTANT: Make sure you don’t use the mop without attaching a micro-fiber pocket and adding water to the tank first. When you are using the mop for the first time, it might take longer than the normal 30 seconds to start steaming. Just pump the handle a few times in a downward motion to prime the pump and it should be ready. A NOTE: Make sure the floors are swept or vacuumed before using the steam mop. 1 Pull and twist the quick release cord holder to unwrap the power cord completely. A great time saver! Plug into a 120-volt electrical outlet The power “On” light will turn blue, it takes approximately 30 seconds for the mop to heat up and the steam to be ready. 2 Pump the handle a few times in a downward motion. This pumping action will release steam as you mop and allows you to customize the amount of steam you want. Begin mopping with a forward and backward motion. The natural motion of mopping will produce steam. 4 a? TOLL FREE: 1-800-798-7398 3 For your comfort, you can adjust the height of the mop. Just lift the latch on the tube 90 degrees to the open position. Holding the handle, extend the tube to the height that’s right for you and then close latch to locked position. 4 When one side of the micro-fiber pocket gets dirty, just flip the mop head and you can quickly start using the other side. Dirt can’t hide on either side. A IMPORTANT: Please wait 3-5 minutes for the Steam Mop to cool off before switching the mop head or the micro-fiber pockets. 5 When the water tank is empty, the steam mop will stop producing steam. You can refill the water tank at any time as long as the mop is unplugged from the outlet. Follow the instructions from page 3. This goes for switching the mop heads or micro-fiber pockets as well. A IMPORTANT: Never leave the steam mop with a damp/wet micro-fiber pocket on any floor surface for any amount of time as this may damage the floor. Using Your Carpet Glider The Steam Mop won’t clean your carpeting or area rugs. However, it’s great for deodorizing and freshening. THE CARPET GLIDER The Carpet Glider can be used with the All-Purpose head to lightly steam your carpet and area rugs. Just place the mop head on top of the glider and move back and forth across a section of the carpet. The steam mop won’t clean your carpeting or areas rugs, but it’s great for deodorizing and freshening. A NOTE: Please note that the Steam Mop rests on top of the carpet glider and it is not a fixed attachment. Do not leave steam mop with carpet glider in one stationary position for any period of time. 6 | a? TOLL FREE: 1-800-798-7398 Care of Your Steam Mop ...