Votes - 3, Average rating: 4
(
)
)
|
manual abstract
The appliance's electrical and electronic parts must not be reused for improper uses since they contain substances which constitute health hazards. 1.4.1 Symbols E2 symbol – Indicates that the appliance is intended for professional use, i.e. for experienced people informed about the relative technical, regulatory and legislative aspects and capable of performing the operations necessary for the use and maintenance of the appliance. E3 symbol – Indicates that the appliance is intended for non-professional (domestic) use. 2 TECHNICAL INFORMATION (FIG.1) 2.1 Envisaged use This appliance has been designed for individual use for the cleaning of vehicles, machines, boats, masonry, etc, to remove stubborn dirt using clean water and biodegradable chemical detergents. Vehicle engines may be washed only if the dirty water is disposed of as per regulations in force. -Intake water temperature: see data plate on the appliance. -Intake water pressure: below 10 bar. -Operating ambient temperature over 0°C in accordance with standard EN 60335-2-79/A1 only for domestic model (see symbol E3). 2.2 Operator The symbol on the front cover identifies the appliance’s intended operator (professional or non-professional). 2.3 Improper use Use by unskilled persons or those who have not read and understood the instructions in the manual is forbidden. The introduction of inflammable, explosive and toxic liquids into the appliance is prohibited. Use of the appliance in a potentially inflammable or explosive atmosphere is forbidden. The use of non-original spare parts and any other spare parts not specifically intended for the model in question is prohibited. All modifications to the appliance are prohibited. Any modifications made to the appliance shall render the Declaration of Conformity null and void and relieve the manufacturer of all liability under civil and criminal law. 2.4 Main components B1 Adjustable spray nozzle B2 Lance B3 Gun with safety catch B4 Power supply cable with plug B5 High pressure hose B6 Detergent tank (on models with this feature) 2.4.1 Accessories (where applicable – see fig.1). C1 Nozzle cleaning tool C2 Rotating nozzle kit C3 Handle C4 Brush C5 Hose reel 2.5 Safety devices Caution - Danger! Do not tamper with or adjust the safety valve setting. -Safety valve and pressure limiting valve. The safety valve is also a pressure limiting valve. When the gun trigger is released, the valve opens and the water recirculates through the pump inlet. -Safety catch (D): prevents accidental spraying of water. 3 INSTALLATION (FIG.2) 3.1 Assembly Caution - Danger! All installation and assembly operations must be performed with the appliance disconnected from the mains power supply. The assembly sequence is illustrated in fig.2. 3.2 Assembling the rotating nozzle (For models with this feature) The rotating nozzle kit delivers greater washing power. 3.3 Electrical connection Caution - Danger! Check that the electrical supply voltage and frequency (V-Hz) correspond to those specified on the appliance data plate (fig.2). The appliance should only be connected to a mains power supply equipped with an adequate earth connection and a differential security breaker (30 mA) to cut off the electricity supply in the instance of a short circuit. 3.3.1 Use of extension cables Use cables featuring “IPX5” protection level. The cross-section of the extension cable should be proportionate to its length; the longer it is, the greater its cross-section should be. See table I. 3.4 Water supply connection Caution - Danger! Only clean or filtered water should be used for intake. The delivery of the water intake tap should be equal to that of pump capacity. Place the appliance as close to the water supply system as possible. 3.4.1 Connection points l Water outlet (OUTLET) n Water inlet with filter (INLET) 3.4.2 Connection to the mains water supply The appliance can be connected directly to the mains drinking water supply only if the supply hose is fitted with a backflow preventer valve as per current regulations in force. Make sure that the hose is at least O 13 mm and that it is reinforced. 11English EN 4.1 ADJUSTMENT INFORMATION (FIG.3) Adjusting the spray nozzle (for models with this feature) Water flow is adjusted by regulating the nozzle (E). 5.4 Restarting 1) Release the safety catch (D). 2) Depress the gun trigger and discharge the residual air inside the hoses. 4.2 4.3 Adjusting the detergent (on models with this feature) Detergent flow is adjusted using the regulator (F). Adjusting the detergent pressure 5.5 3) Set the starter device on (ON/1). Storage 1) Switch the appliance off (OFF/0). Set the adjustable nozzle on " " to deliver detergent at the correct pressure (on models with this feature). 2) Remove the plug from the socket. 3) Turn off the water supply tap. 4.4 Adjusting the pressure (on models with this feature) The regulator (G) is used to adjust the working pressure. The pres4) Discharge the residual pressure from the gun until a...