Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
Never use steam head in a horizontal position or tilt into a backward position, this may result in hot water discharge. 10. To reduce the risk of electric shock, do not immerse the appliance in water or other liquids. 11. Appliance should always be turned off before plugging or unplugging. Never yank the cord to disconnect from outlet, instead grasp plug and pull to disconnect. 12. Do not allow cord to touch hot surfaces. Let appliance cool completely before putting away. 13. Loop cord loosely under the appliance when storing. 14. Do not let power cord contact sharp edges or hot surfaces. 15. Do not try to fasten the nozzle hose guide during operation. Scalding may occur if the nozzle hose guide is removed while using the appliance. 16. Always disconnect appliance from electrical outlet when filling with water, emptying or when not in use. 17. Burns can occur from touching hot parts, hot water or steam. Always use care when you empty a steam appliance. There may be hot water in the reservoir. 18. Do not direct steam at people or animals, or steam clothes while they are being worn. 19. This is a floor appliance and should never be carried while in use. SPECIAL INSTRUCTIONS 1. This is a 1200-watt appliance. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit. 2. If an extension cord is absolutely necessary, the electrical rating should be at least as great as the electrical rating of the appliance. Cords rated for less currency may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. 3. Do not cut or attempt to extend the steaming hose. 4. To reduce the risk of electric shock, this appliance has a polarized plug (One blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY Commercial use of this unit voids the manufacturer's warranty. 1 SETUP Crease Making Tool ► Attach to the syeamer head to use with shirt cuffs and collars and/or creating creases in pants. Lint Removal Brush ► Attach to the syeamer head to remove dust or lint attached to clothing. ► Attach to the steamer head to use when tidying clothing. Crease Clip ► Use to make creases in dress shirts and/or Pressing Glove ► Make sure to put on the pressing glove when using this product. (Exercise care as exposure in excess of one minute of the pressing glove to steam can result in bum injuries). Align properly from the bottom and press firmly to hear a snapping sound as it fastens into place. 2 ASSEMBLY H Step One - Insert the widest end of the telescoping pole into the main unit and secure it by tightening the nut. HI Step Two - Insert the hanger assembly to the top of the pole. HI Step Three - Insert the hose base into the base unit opening and turn it clockwise until in place. | Step Three} HI Step Four - Secure the steam head in place between the prongs, then adjust the height using the clips along the telescopic pole. Turn the plastic screw to secure. PRE-USE INSPECTION O Check to see if any water is leaking from the excess water removal valve. $ Firmly shut the excess water removal valve. (Note: If water overflows, contact the HAAN Customer Care). When inserting the water tank into the main unit, make sure the water has not overflowed. «Make sure the Dower is off. 3 BRUSH ASSEMBLY • Lint Removal Brush Assembly » Bristle Brush Assembly i Fasten lightly to the emission area. 9 Push in the direction of the arrows to fasten completely. □ Fasten lightly to the emission area. 0 Push in the direction of the arrows to fasten completely. • Crease Making Tool Assembly & Usage Place a pressing glove on the left hand and fix the sleeve into the desired position. Affix the crease clip to the sleeve near the shoulder, and then use the crease making tool to create a crease. SK Refer to the left image. WATER DRAINING 1. Cool the garment steamer for at least 30 minutes after each use. 2. Open the excess water removal valve and empty any water remaining in the heater of the main unit. 3. Clean and remove water from the area between the main unit and the water tank to prevent buildup. 4 STEAM PRESS USAGE 0 Fill the water tank to the level according to the desired usage time. A full water tank is capable of continuous steam release for 100 minutes. ® Hold the water tank by its handle and insert securely into the slot in the main unit. @ Align the water refill valve cap properly and screw securely shut. Steam can be released 40-50 seconds after pressing the power button. Pressing the power button again turns the power off. Refill the water tank with water when the water refill lamp turns on. Before use 3 read the instructions for use and Important Safety ...