Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
Power Switch 0 = Off(I= On ) D. Push power switch on, which is located on the back side of the unit. E. Pull up and hold the solution release trigger and apply two spraying strokes by moving the carpet shampooer/extractor forward and then backward at a moderate pace two times. As the nozzle moves over the carpet, the cleaning solution is sprayed onto the carpet. At the same time the nozzle picks up the dirty water and places it in the recovery tank. It is important to move the carpet shampooer/extractor in a steady motion over any surface. F. Release the trigger to stop the solution flow. Avoid over- soaking. G. Move the carpet shampooer/extractor over the carpet several more times without engaging the trigger.This removes excess water and helps the carpet dry faster. H. Repeat steps E, F, and G on heavily soiled areas. Fabric Code Ratings: • W for wet clean. • S-W for solvent-dry or wet clean. • S for solvent-dry clean only. Do not wet clean. Fabric Code Ratings: • W for wet clean. • S-W for solvent-dry or wet clean. • S for solvent-dry clean only. Do not wet clean. . HOW TO PREPARE THE CARPET SHAMPOOER/EXTRACTOR FOR UPHOLSTERY AND STAIR CLEANING (only for models with an attachment hose and upholstery/stair cleaning nozzle) Vacuum Upholstery or Stairs Vacuum upholstery and stairs with a vacuum cleaner’s attachment tool. Use a crevice tool for hard to reach areas such as tufts and corners. IMPORTANT: Cleaning some upholstery fabrics with a wet cleaning solution may damage the fabric. Know what the fabric content is and how to clean it before using a cleaning solution on upholstery fabrics. Most manufacturers care code their fabrics with cleaning methods. Some very delicate and unusual fabrics are DRY CLEAN ONLY. If in doubt of the fabric type, call a dealer or take a cushion or arm cover to a dealer for advice. Check the stuffing material if possible Look inside the cushions or on the underneath side. If filling is a dark color, it may bleed through and discolor the fabric. Most stuffing material that is white to light yellow is colorfast and will not bleed colors through to the fabric covering. Test clean a hidden area Be sure to test clean a hidden area several hours before starting to clean. Let the test area dry completely. Inspect for changes in color, bleeding, stretching, or shrinking. Test another area if in doubt. Pretest for Color Fastness Before cleaning the upholstery, we recommend testing it for color fastness. Moisten a white towel with the cleaning solution.Test a small area of the cushion back. Gently rub the cloth over the area. Check each area for color bleeding. If the towel does not pick up any color, it should be safe to use the cleaning solution on the entire area. VII. HOW TO USE THE CARPET SHAMPOOER/EXTRACTOR FOR UPHOLSTERY OR STAIR CLEANING (only for models with an Attachment Hose and Upholstery/Stair Cleaning Nozzle) NOTE: Use extra caution when cleaning on stairs. To prevent the carpet shampooer/extractor from falling, do not place the unit on stairs. It is suggested that the carpet shampooer/extractor be placed at floor level to clean the lower portion of the stairs and be securely placed at the top of the stairway to clean the upper portion of the stairs. Clean Water Solution Tank A. Turn selector knob to the Attachment Mode. B. Lift the attachment hose from the tool caddy on the back of the shampooer/ extractor. Selector Knob How to Use the Carpet Shampooer/Extractor for Upholstery and Stair Cleaning (Continued) How to Use the Carpet Shampooer/Extractor for Upholstery and Stair Cleaning (Continued) Solution Release Trigger C. Place the Upholstery Nozzle at the top of the cleaning area. D. Pull up and hold the solution release trigger and pull the nozzle backward at a moderate pace. E. Release the trigger at the end of the stroke. F. Lift nozzle and start again at the top. Apply one to three spraying strokes. Avoid over-soaking the area. NOTE: As the nozzle moves over the surface, the cleaning solution sprays onto the surface. At the same time the nozzle picks up the dirty water and places it in the recovery tank. G. Move the nozzle over the surface several more times without engaging the trigger. This removes excess water and helps the surface dry faster. H. Brush roll does not rotate when cleaning in the attachment mode. NOTE: If the cleaning solution and water are not released from the upholstery/stair nozzle, there may be an air lock. With unit in the Off position, raise the attachment handle above your head.Then engage the attachment handle trigger for 4 seconds.Turn unit On to resume spraying. NOTE: If you should encounter a clog in the Upholstery/Stair Nozzle Filter: 1) Remove the “M” shaped piece on the underside of the Upholstery/Stair Nozzle (Use a small screwdriver to pry loose). 2) Clear and rinse any debris from the “M” shaped piece by placing it under running water. 3) Replace the “M” shaped piece into the solution tube then position and lock the piece into place. ...