Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Advice Carefully read the complete procedure before starting! You do not know the brand of your equipment/you can not find the right code in the code list » auto search: TV VCR SAT 1 3 1 Press the mode selector key to select the device (TV, VCR or SAT) you want to operate. 2 Make sure the device is switched on (if the device is a VCR, please insert a tape and start playback). 3 Press and hold keys 1 and 3 simultaneously -for about three seconds- until the green LED lights up. (Release the keys: the green LED should stay on) 4 Instructions for use XP SBC RU 631/00 2002 15-10-2001 12:35 Pagina 5 XP SBC RU 631/00 2002 15-10-2001 12:35 Pagina 5 4 Press the power key to start the search. Make sure that you keep the remote control pointed at your equipment. – Each time the green LED flashes, another code is sent. When the right code is found, the equipment switches off. Immediately press the power key to stop the search. If the green LED flashed again after the equipment switched off, this means you missed the correct code! If you missed the code, follow the next procedure, starting at step 5. If the LED did not flash again after the equipment switched off, go to step 7. PROG 5 Switch the equipment manually back on. 6 Press ‘PROG-’ (down only!) repeatedly to send previous codes until the equipment switches off again. 1 6 1 2 3 TV VCR SAT 7 Press the power key to lock the correct code in the SBC RU631’s memory. – The green LED flashes twice. Check Switch equipment on manually. Press a few keys to check correct response. If response is not correct, repeat procedure beginning at step 1. Note -The search time averages about 90 seconds. (Maximum search time is 5 minutes for TV, 2 minutes for VCR and 4 minutes for SAT). -Autosearch stops automatically after all codes have been tested. MAKE A NOTE OF YOUR CODE! Advice Carefully read the complete procedure before starting! Note the code inside the battery case and in the codelist in the centre of this booklet. This may be useful if you ever need to set up the SBC RU631 again. You used the auto search procedure or you forgot to note the code after set up? No problem! You can still ‘read out’ the code from the remote: 1 Make sure you’ve selected the right mode with the mode selector key. 2 Press and release keys 1 and 6 simultaneously. Important: after pressing the keys, you have to release them immediately! – The green LED lights up. 3 Press the two digits key. – The green LED goes out. 4 Press key 1 and count the number of times the green LED flashes. This is the first digit of the 4-digit code. (No flashes means the digit is zero.) 5 Press key 2 and count the number of flashes for the second digit. 6 Press key 3 and count the number of flashes for the third digit. 5 English Instructions for use XP SBC RU 631/00 2002 15-10-2001 12:35 Pagina 6 XP SBC RU 631/00 2002 15-10-2001 12:35 Pagina 6 4 English 7 Press key 4 and count the number of flashes for the forth digit. 8 Note the code. ADVANCED TIPS AND TRICKS Advice Carefully read the complete procedure before starting! Changing the device keys With the mode selector it is possible to select 4 categories of devices you want to operate. Each category (TV, VCR, SAT and DVD) is meant to operate a specific group of equipment: TV VCR SAT tv vcr sat cable Once you have programmed the functions of a device in one of the categories, it is not possible to program another device in the same category. There is, however, a solution in case you want to program two devices in the same category (2 TV’s, VCR’s, etc.). The following example explains how. EXAMPLE: The SAT mode on this remote control is factory preset to control many Philips satellite receivers. You can change the SAT mode (or any mode) to operate another type of device. The following example shows you how to use the SAT mode to operate a second TV: 1 Press the mode selector key to select SAT and make sure the second TV is switched on. 2 Press and hold keys 1 and 6 simultaneously -for about 3 seconds- until the green LED lights up. 3 On the keypad, press keys 9, 9 and 2. 4 Press the mode selector key to select TV mode. 5 Press key 1. – The LED flashes twice to indicate successful set up. That’s it! Don’t forget to set up the SBC RU631 to operate this second TV. See the section Set-up for use. 1 9 9 2 1 6 TV VCR SAT TV VCR SAT 6 Instructions for use XP SBC RU 631/00 2002 15-10-2001 12:35 Pagina 7 XP SBC RU 631/00 2002 15-10-2001 12:35 Pagina 7 9 9 3 1 6 TV VCR SAT TV VCR SAT 1 9 Punch-Through Sound Punch-through sound enables you to control the audio level of your first or second TV, regardless of what device mode the remote control is in. EXAMPLE: You have installed a second TV under SAT mode. You can control that TV’s volume when you are in VCR mode. This feature is installed as a default setting for a first TV. To install this feature for a second TV: 1 Press the mode selector key to select VCR. 2 Press and hold keys 1 and 6 simultaneously -for about 3 seconds- until the gr...