Votes - 0, Average rating: 0
(
)
)
|
manual abstract
5 Instructions for use English 6 Check if you can operate all functions on your TV with the SRU 5060. • If this is not the case, you can redo the automatic setting. The SRU 5060 will then search for a code that works better. – After the SRU 5060 has run through all the known codes, the search will stop automatically and the Standby key will stop flashing. – Automatic programming of a TV takes a maximum of 5 minutes. For DVD, CD, VCR, AMP and STB this time is 2 minutes. Manually setting the remote control Example of TV: 1 Turn on the TV manually or use the original remote control. Tune in to channel 1. 2 Look up the brand of your TV in the code list at the back of this manual. One or more four-figure codes are shown for each brand. Note the first code. Be careful! There are separate tables for TV, video, DVD, etc. On our website you can directly select your device typenumber to find the tight code. Make sure you use the codes from the correct table. 3 Press the SELECT key to select TV. Press the key until the Standby key lights up. 4 Keep keys 1 and 3 pressed simultaneously for three seconds until the Standby key flashes twice and then remains lit. 5 Then enter the code noted in step 2 using the digital keys. – The Standby key will now flash twice. If the key flashes once for an extended period, the code has not been entered properly or the wrong code has been entered. Star t again from step 2. 6 Point the SRU 5060 at the TV and check that it responds as it should. – If the TV responds to all of the key commands, the SRU 5060 is ready for use. Do not forget to note your code. • If the device does not respond at all, or not to all of the key commands, start again from step 2 and try the next code from the list. 6 Instructions for use 3. Keys and functions The illustration on page 3 gives an overview of all keys and their functions. English 1 y Standby . . . . . . . . . . switches TV,VCR, CD, DVD, STB or AMP on or off. 2 LEARN. . . . . . . . . . . . . switches the SRU 5060 into learning mode. 3 . . . . . -teletext on/off ( ); -text off ( ); -wide screen TV ( ); -text hold ( ). 4 MENU. . . . . . . . . . . . . . turns the menu on and off. 5 Cursor keys . . . . . . . . cursor up, down, left, right in a menu. -REAR + / -CENTER + . . . . . . . . adjusts the volume of the centre and rear speakers in surround mode. 6 AV . . . . . . . . . . . . . . . . . switches between external inputs of your equipment. 7 s. . . . . . . . . . . . . . . . . . . mutes the sound of the TV. 8 - VOL + . . . . . . . . . . . . . adjusts the TV volume. 9 Digit keys . . . . . . . . . . -direct choice of channels and other functions. -source selection keys in amplifier mode (together with SHIFT). 0 SHIFT. . . . . . . . . . . . . . for extra functions.When pressed at the same time as a second key, the second key will get another function. All blue labelled keys can be used together with SHIFT. For example: SHIFT + INSTALL . installs your TV SHIFT + STORE. . . . stores TV settings SHIFT + TV: . . . . . . . . selects TV as input source for amplifier SHIFT + DVD:. . . . . . selects DVD as input source for amplifier Try out other combinations with the SHIFT-key on your device in order to find out which functions are available. Only functions featured on the original remote control are available. ! 5 . . . . . . . . . . . . . . . . . . -red teletext key -rewind (VCR/DVD) 2 . . . . . . . . . . . . . . . . . . . -index -play (VCR/DVD) 6 . . . . . . . . . . . . . . . . . . -blue teletext key -wind (VCR/DVD) 9 . . . . . . . . . . . . . . . . . . . -green teletext key -stop (VCR/DVD) 0 . . . . . . . . . . . . . . . . . . . record ; . . . . . . . . . . . . . . . . . . . -yellow teletext key -pause (VCR/DVD) @ /. . . . . . . . . . . . . . . . . . selects between one-and two-figure channel numbers. # 2 22 / SURROUND . . - selects previous programme/channel. -selects surround modes. $ - PROG +. . . . . . . . . . . selects a previous or following channel. % GUIDE . . . . . . . . . . . . . opens electronic TV program guide (STB). ^ OK . . . . . . . . . . . . . . . . . confirms your selection. & BACK . . . . . . . . . . . . . . jumps back one level in the menu or turns off the menu. * SELECT. . . . . . . . . . . . selects TV,VCR, CD, DVD, STB or AMP mode. 7 Instructions for use English • If the device does not respond at all, or not to all of the key commands, follow the instructions under ‘Setting the remote control’. It is possible that you must enter another code for the device. 4. Extra possibilities Adjusting device selection (Mode selector) The SRU 5060 is default set for operating TV, VCR, CD, DVD, STB (settop box, satellite or cable decoder) and AMP (amplifier). You can select the device you wish to operate with the SELECT key (mode selector). Each option allows operation of one device only. If desired, you can program the SELECT key (mode selector) to select a different kind of device. For example, if you want to operate a second T...