Votes - 0, Average rating: 0
(
)
)
|
manual abstract
3 9 2 Getting started ........................................... 4-8 2.1 Inser ting the batteries ....................................4 2.2 Setting up the universal remote control................................................................ 4-8 3 Using the universal remote control ........................................................ 8-10 3.1 Buttons and functions..............................8-10 3.2 Resetting a button to its original function................................................................ 10 4 Service and support ..............................11-14 4.1 Frequently asked questions ...............11-13 4.2 Need help? ........................................................ 13 FCC Compliancy.....................................13-14 Notice for Canada ........................................ 14 Helpline ............................................................... 15 Brand list ......................................................16-28 Information to the consumer....................29 Compliance with EMF................................. 29 Recycling and disposal................................. 29 1 Your SRP2104 Congratulations on your purchase of the Philips SRP2104 universal remote control. After setting up the remote control you can operate up to 4 8 different devices with it. Simple Setup Improved with Philips patented (pending) Simple Setup technology, the SRP2104 can be set up easily for TV, DVD player / recorder,VCR and all common Cable, Satellite and other set top boxes, such as DirecTV, Comcast, AT&T,Verizon, Time Warner, Scientific Atlanta, Tivo and many more. Simply follow the instructions in chapter 2.2 to set up the remote control for your devices. Glow buttons The remote control glow buttons (-VOL +, CH +, ENTER. (-) and the numeric buttons) light up in the dark, enabling easy use of the remote control, even in a dimly lit room To fully benefit from the suppor t that Philips offers, register your product at: EN 3 Your SRP2104 English 4 EN EN 5 2 Getting started 2.1 Inserting the batteries • Insert 2 AAA type batteries, noting the + and - configuration in the battery compartment. Note When replacing the batteries, all user settings will be retained in the remote control memory for 5 minutes. 2.2 Setting up the universal remote control The example below instructs you how to set up your universal remote controls for your TV. You can repeat the same steps for other devices (DVD player/recorder, Cable/Satellite box and VCR) which you want to operate, using the SRP2104. The remote control can be set up to operate any 4 of the following devices: Device name Description TV Traditional TV, flat screen TV and projection TV, TV part of TV / VCR, TV / VCR / DVD and TV / DVD combos DVD DVD player / recorder (DVDR), DVD / Hard Disk Drive combination (DVDR-HDD), Blu-Ray player, High Definition DVD player (HD-DVD), DVD part of TV / DVD, TV / VCR / DVD and VCR / DVD combos CBL/SAT Cable box, satellite receiver, Internet Protocol TV (IPTV), Free To Air TV, High Definition Television decoder (HDTV) and Tivo VCR Video cassette player / recorder, Personal video recorder (PVR), VCR part of TV/VCR, TV/VCR/DVD and VCR/DVD combos Example: setting up the universal remote control to operate your TV: 1 Switch ON the TV manually or use the original remote control for this. Tune to channel 1. 2 Press and hold the device selection button for 5 seconds until the red Setup light remains lit . The remote control is now in setup mode. 3 Look up the 4-digit code for your brand in the brand list at the back of this user manual. A 4-digit code is shown for each brand. Use the digit buttons to enter the code for your brand. • If the red Setup light turns off, an invalid code was entered. In this case, try again. 4 Aim the remote control at the TV. Press and hold the button. Release it immediately as soon the TV switches off. • This step normally takes between 5 and 60 seconds. In extreme circumstances this step can take up to 15 minutes. Getting started English 5 sec. 5 - 60 sec. 5-60 SEC. 6 EN EN 7 5 Switch ON the TV. Try out the buttons you need for operating it. Try, for example, if the - CH + and digit buttons function properly. • If a button does not work as expected, press and hold that button. Release it immediately as soon as it works. For more information, see chapter 2.2.2. 6 Press the device selection button twice to finish setup. • When no button is pressed for 5 minutes or more, the remote control will exit setup mode, automatically saving all your settings. Important If you made a mistake: • Press the device selection button twice to exit setup. The red Setup light turns off. • Restart from the beginning. • If the device does not respond at all or not to all of the button commands or if you cannot find the code for your brand, enter ‘9, 9, 9, 9’ in step 3 and continue with step 4. The remote control will now search its full database for a code that works with your TV. F...