Votes - 0, Average rating: 0
(
)
)
|
manual abstract
0 AV . . . . . . . . . . . . . . . . . switches between external inputs of your equipment. ! 5 . . . . . . . . . . . . . . . . . . -TV mode: red teletext key*. -VCR/DVD mode: rewind. 2 . . . . . . . . . . . . . . . . . . . -TV mode: index. -VCR/DVD mode: play. 6 . . . . . . . . . . . . . . . . . . -TV mode: blue teletext key*. -VCR/DVD mode: wind. 9 . . . . . . . . . . . . . . . . . . . -TV mode: green teletext key*. -VCR/DVD mode: stop. 0. . . . . . . . . . . . . . . . . . . -VCR/DVD mode: record. ; . . . . . . . . . . . . . . . . . . . -TV mode: yellow teletext key*. -VCR/DVD mode: pause. @ -/--. . . . . . . . . . . . . . . . . . selects between one-and two-figure channel numbers. # 2 22. . . . . . . . . . . . . . . . . . -selects previous programme / channel. SURROUND . . . . . . . -selects surround modes. $ - PROG +. . . . . . . . . . . selects previous or next channel. % BACK . . . . . . . . . . . . . . jumps back one level in menu or turns off menu. ^ Cursor keys . . . . . . . . cursor up, down, left, right in a menu. & GUIDE . . . . . . . . . . . . . STB mode: opens electronic TV programme guide. * y yy (Standby) . . . . . . . . . . switches TV, DVD,VCR, AMP, CD or STB on or off. ( SETUP . . . . . . . . . . . . . -switches the remote control into setup mode. SELECT. . . . . . . . . . . . -turns on the backlight (if enabled). -selects device modes. Only devices for which the remote control is set up can be selected. * Note: If you wish to use the colour keys as colour selection keys in DVDR-HDD mode, you should learn the colour selection functions to the extra function key XTRA. For this, see ‘Adding extra functions’ under 4. ’Extra possibilities’. Extra functions For each device, the remote control is set up for, extra (advanced) functions can be added to the remote control. For this see ‘Adding extra functions’ hereafter. For an overview of extra (advanced) functions for the various devices, see the ‘Extra functions’ list at the back of this booklet. English 7 English English Instructions for use 4. Extra possibilities Adding extra functions Note: Only functions that are available on the original device remote controls can be added. 1 Keep XTRA pressed for 3 seconds: – - the backlight (if enabled) turns on. -the display shows ‘ ’ and ‘ ’. - the keys that can be used are blinking. 2 Use 3 and 4 to select the extra function you wish to add or change. Confirm with OK. – The display shows ‘ ’, ‘ ’ and ‘ ’ together with ‘LEARNING‘. 3 Place both remote controls on a flat surface (like a coffee table) and aim them head-to-head with about 5 - 10 cm in between. 4 Press the function key on the original remote control (e.g. the AMBILIGHT key on your TV remote control) or press 1 if you wish to return to step 2. – The display shows ‘ ’ together with e.g. ‘TV-AMBILIGHT LEARN OK‘. The extra function has been added successfully. – If the display shows ‘ERROR‘ or ‘MEM FULL’, star t again from step 1. Also see ‘Troubleshooting’ under 6. ‘Suppor t’. Activating / using an extra (advanced) function 1 Use SELECT to select the desired device. E.g. DVD. – Confirm with OK. 2 Press XTRA. – The last selected function for the device appears on the display. E.g. DVD-SHOWVIEW. The keys that can be used are blinking. 3 Use 3 and 4 to select the function you wish to activate. E.g. DVD-ZOOM. Press OK to activate the function. 4 Press XTRA again to go back to normal operation mode. Delete devices Example of TV: 1 Keep SETUP pressed for 3 seconds: – the backlight (if enabled) turns on. – ‘ ‘ ’ and ’TV?’ – the keys that can be used are blinking. 8 Instructions for use 2 Use 3 and 4 to select ’DELETE TV’ at the bottom of the list. 3 Press OK to delete the TV device mode. – The display shows ’DEVICE DELETED’. – The TV device mode has been deleted. Learning key functions If you miss cer tain functions from your original remote control on the SRU 5170, it can learn these functions from the original remote control. You can store a function under any of the available keys on the SRU 5170, except XTRA (LEARN) and SELECT (SETUP). Any function already stored under a key will be deleted. 1 Make sure you have the original remote control at hand. 2 Use SELECT to select the desired device. E.g. DVD. 4 Keep LEARN and the key you wish to learn on the SRU 5170 pressed simultaneously for 3 seconds, ’ lights up, together with ’LEARNING’. 5 Press the key you wish to copy on the original until ‘ remote control. – lights up. The remote control is now learning the function. – When the remote control has learned the function, the display shows ’LEARN OK’ to confirm that the signal is stored. – If the display shows ‘ERROR‘ or ‘MEM FULL’, star t again from step 1. Also see ‘Troubleshooting’ under 6. ‘Suppor t’. Place both remote controls on a flat surface (like a coffee table) and aim them head-to-head with about 5 - 10 cm in between. English 9 Instructions for use English Activating / de-activating the backlight function The backlight illuminates the displa...