Votes - 0, Average rating: 0 ( )

Manafacture: Philips File size: 1.22 mb File name: Language of manual:

MENU OK SHIFT 1 2 3 4 5 6 7 8 0 9 5 Then enter the code noted in step 2 using the digital keys. – The green light in the selector window will now flash twice. If the light flashes once for an extended period, the code has not been entered properly or the wrong code has been entered. Star t again from step 2. 6 Point the RU530 at the TV and check that it responds as it should. – If the TV responds to all of the key commands, the RU530 is ready for use. Do not forget to note your code. • If the device does not respond at all, or not to all of the key commands, start again from step 2 and try the next code from the list. 6 Instructions for use XP SBC RU 530/87.3 09-02-2004 15:31 Pagina 7 XP SBC RU 530/87.3 09-02-2004 15:31 Pagina 7 English Automatically setting the remote control If you cannot find the right code for your brand device, the remote control can automatically search for the right code. Example of TV: 1 Make sure the TV is switched on and select a channel using the original remote control or the keys on the TV (for example channel 1). The RU530 emits the ‘switch off TV’ signal for all models of TV that are stored in the memory. • If the device is a video recorder, inser t a tape and star t playback. 2 Then keep keys 1 and 3 on the RU530 pressed simultaneously for three seconds, until the green light under TV in the selector window flashes twice and then remains lit. TV VCR SAT TV VCR SAT MENU OK SHIFT 1 2 3 4 5 6 7 8 0 9 3 Press the Standby key of the RU530 briefly. – The RU530 now star ts emitting all known ‘TV off ’ signals, one by one. Each time a code is sent, the green light under TV in the selector window lights up. 4 When your TV switches off (stand-by), you press the Standby key of the RU530 twice within 1 second, to confirm. – The RU530 has now found a code that works on your TV. 5 Check if you can operate all functions on your TV with the RU530. TV VCR SAT 2x • If this is not the case, you can redo the automatic setting. The RU530 will then search for a code that perhaps works better. – After the RU530 has run through all the known codes, the search will stop automatically and the green light will stop flashing. – Automatic programming of a TV takes a maximum of 5 minutes. For VCR this time is 2 minutes and for SAT 4 minutes. 7 Instructions for use XP SBC RU 530/87.3 09-02-2004 15:31 Pagina 8 XP SBC RU 530/87.3 09-02-2004 15:31 Pagina 8 English 3. Keys and functions The illustration on page 3 gives an overview of all keys and their functions. 1 y Standby . . . . . . . . switches TV, VCR or SAT mode on or off. 2 Mode-selector . . . . selects the device you want to operate: TV, VCR or SAT (satellite/cable). 3 s . . . . . . . . . . . . . . . . mutes the sound of the TV. 4 - VOL +. . . . . . . . . . . adjusts the TV volume. 5 MENU . . . . . . . . . . . turns the menu on and off. 6 Digital keys . . . . . . . direct choice of channels and other functions. 7 SHIFT . . . . . . . . . . . for extra functions. When pressed at the same time as a second key, the second key will get another function. For example: SHIFT + PROG+: . 'menu up' SHIFT + PROG-:. . 'menu down' SHIFT + VOL+: . . . 'menu right' SHIFT + VOL-: . . . 'menu left' Tr y out other combinations with the Shift-key on your appliance in order to find out which functions are available. Only functions featured on the original remote control are available. 8 1 . . . . . . . . . . . . . . . . - red teletext key -rewind (VCR) 9 9 . . . . . . . . . . . . . . . . - green teletext key -stop (VCR) 0 0 . . . . . . . . . . . . . . . . tv: P1P, previous channel VCR: record SAT: A/B ! ;. . . . . . . . . . . . . . . . . - yellow teletext key -pause (VCR) @ 6. . . . . . . . . . . . . . . . - blue teletext key -wind (VCR) # 2 . . . . . . . . . . . . . . . . - white teletext key -index - play (VCR) $ / . . . . . . . . . . . . . . . . selects between one- and two-figure channel numbers. % OK. . . . . . . . . . . . . . . confirms your selection. ^ - PROG + . . . . . . . . selects a previous or following channel. & AV . . . . . . . . . . . . . . . switches between external inputs of your equipment. * . . . . . . . . TV: teletext keys SAT: teletext, Info, Guide, Subtitle VCR: timer, Showview If you use the (fi) 'memory off' key to get to the next teletext page on your Philips TV, you can press the Subtitle key for this. See also ‘Troubleshooting’. • If the device does not respond at all, or not to all of the key commands, follow the instructions under ‘Setting the remote control’. It is possible that you must enter another code for the device. 8 Instructions for use XP SBC RU 530/87.3 09-02-2004 15:31 Pagina 9 XP SBC RU 530/87.3 09-02-2004 15:31 Pagina 9 English 4. Extra possibilities Adjusting device selection (Modeselector) The RU530 is default set for operating TV, VCR and Sat (satelliet)/ CBL (cable). You can select the device you wish to operate with the Mode selector. Each option allows operation of one device only. If desired, you can program the Mode s...

Download now

Please, enter two numbers from picture: