Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
In accordance with the "Moss-Magnuson Warranty Act" of July 10, 1975, this is termed a "limited warranty" which in no way compromises Crosley Radio‚ high standards of Quality and Workmanship. 6. Telephone is then mounted according to procedure detailed in MOUNTING TO MODULAR PLUG. NOTE: If you encounter difficulty fitting the telephone body onto the screw, or thetelephone wobbles when installed, either tighten or loosen then screw to adjust. MAKING AND ANSWERING CALLS To get a dial tone or answer an incoming call, lift the handset. To hang up, either replace the handset or simply press the HANDSET CRADLE. IN CASE OF DIFFICULTY If you are having problems with your telephone, try the following suggestion. NO DIAL TONE 1. Make sure that all plugs are connected properly. Check the connections at the walljack, the telephone cabinet and handset. 2. Try another modular jack within your home which you know to be working properly. CALLS CANNOT BE DIALED OR DIALED SLOWLY Check to make sure that the DIAL MODE switch is in the correct position for the typeof service available in your area. TELEPHONE DOES NOT RING Check that RINGER CONTROL switch is not set to OFF. If there are several telephones connected to the same line, try disconnecting some of the other telephones. Having too many telephones connected to the same line can cause low ringer volume or poor sound quality during calls. CARE AND MAINTENANCE Avoid rough treatment to the telephone. Do not drop the handset and always replace it gently onto the cradle. Clean only with a cloth slightly dampened with water only. Do not use detergent, waxes, solvent, spray, alcohol or excessive water. LAST NUMBER REDIALING To redial the last number dialed, momentarily depress the center disk. To Install Wall Anchors If the location you have chosen to mount your telephone is a hollow wall without any beams you will have to use the included wall anchors. To install, place the template against the wall where you wish to place your telephone. Mark the wall at the location of the two + on the template by pushing a pen or pencil through the template. Drill a 1/4" hole at each mark. Push the wall anchor into the hole and gently tap until it is flush with the wall. With a phillips screwdriver, begin tightening the screw. CLOCKWISE. Stop turning when you feel firm resistance. Turn the screw counter clockwise until the screw head is about 1/4" out of the wall. Install the 7 foot line cord at back of the telephone . Adjust the switches to your preference. Position the line cord through the slot on the bottom of the cabinet. Line up the holes with the two screws. Place the telephone onto these two screws and gently pull down. This may require a little fine tuning until the phone is seated securely. W WWALL ANCHOR ALL ANCHORALL ANCHOR PRIOR T PRIOR TPRIOR TO INST O INSTO INSTALLA ALLAALLATION TIONTION 1/4" HOLE1/4" HOLE W WWALL ALLALL AFTER INST AFTER INSTAFTER INSTALLA ALLAALLATION TIONTION Set UpDIAL MODE Locate the DIAL MODE switch on the rear of the telephone body. Slide the switch toTone unless you have Dial-Pulse (Rotary) telephone service in your area in whichcase, slide the switch to the PULSE position. RINGER CONTROL The RINGER CONTROL switch is on the rear of the telephone body. It allows you toturn the ringer OFF or set it to ring at either LOW or HIGH volume. You can still makeor receive calls with the ringer in OFF position, however, you will not hear the incomingring. RECEIVER VOLUME The RECEIVER VOLUME CONTROL switch, located on the rear of the telephonebody, allows you to adjust the volume of the receiver earphone from LO, MID and HI. HANDSET CORD To assemble, insert one end of handset cord into the HANDSET CORD JACK and the other end to the HANDSET CORD JACK located on the left side of the telephonebody. Installation MODULAR WALL JACK To install the telephone directly on a modular wall jack : 1. Connect the 15 inch line cord to the LINE CORD jack on the rear of the telephonebody. 2. Tuck the line cord into the channel on the cabinet rear. 3. Peel and stick the rubber pads on rear of telephone cabinet in designated areas. 4. Hold the telephone body up next to the modular jack and plug the line cord into thisjack. 5. Tuck the excess line cord into the recess provided on the rear of the telephonebody. 6. Line up the mounting holes of the telephone body with the mounting studs (screwheads) on the modular jack or wall. 7. Push the telephone body against the wall jack and down until it is held securely inplace by the mounting studs. WALL If you are not mounting directly onto a modular wall jack, proceed as follows : 1. Install the 7 foot line cord into the LINE CORD jack on the rear of the telephonebody. If the desired location is further than 7 foot from a wall jack, you will have toobtain a longer line cord available at most hardware stores. 2. Place the provided TEMPLATE against the wall in the position desired. 3. Mark the wall by poking either a pen or pencil through the in...