Votes - 6, Average rating: 3.5 ( )

Manafacture: Cortelco File size: 36.99 kb File name: Language of manual:

OWNER’S INSTRUCTION MANUAL 25002500250025002500255425542554255425542500XX 2500XX2500XX2500XX2500XX2500XX- -----VBA VBAVBAVBAVBAVBA-20MT -20MT-20MT-20MT-20MT-20MT2554XX 2554XX2554XX2554XX2554XX2554XX- -----VBA VBAVBAVBAVBAVBA-20MT -20MT-20MT-20MT-20MT-20MT **”XX” is color code VALUE LINE VALUE LINEVALUE LINEVALUE LINEVALUE LINEVALUE LINE INSTALLING YOUR TELEPHONE MODULAR JACKS To install your telephone, you must have a modular wall jack at the desired location. If your telephone line does not have a modular jack, you must have one installed. DANGER: To reduce the risk of electrical shock and personal injury, observe the following when installing station wiring: 1. Never install telephone wiring during a lightning storm. 2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 3.Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 4.Use caution when installing or modifying telephone lines. Various types of modular wall jacks are shown below. The USOC RJ11C modular wall jack is for desk telephones and the USOC RJ11W modular wall jack is for modular wall telephones. The USOC RJ11W modular wall jack must be in the correct mounting position before mounting a modular wall telephone. Check to make sure it is in the position shown. DESK INSTALLATION To install a desk telephone, use the long modular line cord supplied with your telephone. Plug one end of the line cord into the connector on the back of your telephone and the opposite end into the modular wall jack. Your telephone is ready to use. To disconnect your telephone, press the spring clip on the line cord plug and pull out. WALL INSTALLATION To install a modular wall telephone, refer to the diagram to the right. • Fit the plug (1) on the ack of the telephone into the jack (2). • Align slotted holes (3) on the back of the telephone over the mounting studs (4). • Gently pull down on the telephone until it locks in place. BEFORE USING YOUR TELEPHONE This telephone includes a Handset with Receiver Volume Control that complies with FCC Part 68 requirements mandated by the Hearing Aid Compatibility Act of 1988. The Volume Control is a small switch found on the inside of the Handset handle. The switch may be conveniently operated while holding the handset. Pushing the switch toward the Receiver (upper) end of the Handset will increase the loudness from the Receiver. Pushing the switch toward the Microphone (lower) end of the Handset will decrease the loudness from the Receiver. The Volume Control will not disable the Receiver. The minimum loudness setting of the Volume control will usually produce a comfortable listening level for persons with no hearing impairment. Your telephone has a TONE-PULSE switch. Set the switch to match the dialing service from the telephone company. • If you have pulse service, set the Tone-Pulse switch to PULSE. • If you set the switch for TONE service, you must have TONE service or you cannot dial. • If you set the switch for PULSE service and you have TONE service, you can dial numbers, but you cannot use touch-tone services. • If you have PULSE service you can set the switch to PULSE and dial a touch-tone service, and then set the switch to TONE to use the service. BE SURE TO SET THE SWITCH TO PULSE WHEN YOU FINISH THE CALL. TELEPHONE SERVICE PROBLEMS If you have any problems with your telephone service, determine if the problem is with your telephone or the telephone company lines BEFORE CALLING THE TELEPHONE COMPANY. Please be aware that they may charge you for a service call if the problem is caused by your telephone. NO DIAL TONE • Unplug your telephone from the wall jack. Plug a substitute telephone that is known to work properly into the same wall jack. • If the problem persists when using the substitute telephone, notify the telephone company. • If the substitute telephone works properly, you must have your telephone repaired before reconnecting it to the wall jack. DIAL TONE BUT NO RINGING • Set the RINGER VOLUME CONTROL to HIGH and have someone on another line call you. Before answering the call, set the RINGER VOLUME CONTROL to the desired volume. DIAL TONE BUT NO DIALING • Set the TONE/PULSE switch. You cannot dial out in TONE position if you have Rotary Dial Service. • For Rotary Dial Service, set the switch to PULSE position. • For Tone Dial Service, set the switch to TONE position. • Try both positions if you are not sure. REPAIR OF YOUR TELEPHONE DO NOT ATTEMPT TO REPAIR THE TELEPHONE YOURSELF. Telephones manufactured by CORTELCO VALUE LINE must be returned to us for repair. You can return your telephone to CORTELCO VALUE LINE for repair or replacement in accordance with our LIMITED WARRANTY. DATE-OF-PURCHASE CORTELCO VALUE LINE warrants telephones against defects in material and workmanship in accordance with our LIMITED WARRANTY. If your telephone is returned for repair, include a copy of your ...

Download now

Please, enter two numbers from picture: