Votes - 1, Average rating: 5
(
)
)
|
manual abstract
The telephone should never be placed near or over a radiator or heat register. The telephone should never be placed in a built-in installation unless proper ventilation is provided. 9. Never spill liquid on the telephone or push objects of any kind throughventilation slots. Liquid or objects may touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock. 2 10. Do not disassemble this product. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electrical shock when the product is subsequently used. 11. Do not overload outlets and extension cords. Some telephones require AC power from an outlet. Overloading the outlets can result in the risk of fire or electric shock. 12. Avoid using a telephone during a local thunderstorm. There may be a remote risk of electrical shock from lightning. 13. Do not use a telephone to report a gas leak in the vicinity of the leak. 14. Unplug the telephone from the wall outlet and refer servicing toqualified service personnel under the following conditions: • When the line cord is frayed or plugs damaged. • If liquid has been spilled into the telephone. • If the telephone has been exposed to rain or water. • If the telephone does not operate properly by following the operating instructions. (Adjust only those controls covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.) • If the telephone has been dropped or the housing damaged. • If the telephone exhibits distinct change in performance. SAVE THESE INSTRUCTIONS 15-101-613 3 TELEPHONE USAGE SET UP/INSTALLATION 1. Connect the adapter. Plug the large part of the adapter into the wall outlet and the adapter tip into the jack at the rear side of the unit. Use the enclosed adapter. 2. Connect the telephone line cord. a. To connect without an answering machine. • Use the new line cord to connect the PHONE jack of your new phone to the modular wall jack. b. To connect with an existing answering machine. • Use the existing line cord supplied to connect the LINE jack of your answering machine to the wall modular line jack. • Use the new line cord supplied to connect the telephone’s jack of your new phone to the PHONE jack of your answering machine. • Set your answering machine to answer the phone after 2 or more rings. 3. Remove plastic insulator from the battery compartment located under the directory card to allow proper functioning of battery. 4. Place the unit on a flat table or mount it on a wall. If you desire to place it on a wall, use the wall mount bracket and short line cord supplied to accomplish the wall mounting. 4 WALL MOUNT INSTRUCTIONS 1. Install wall mount bracket in wall mount position and route cords as shown in diagram below. 2. Connect the line cord. See Step 1 on preceding page for specific instructions. 3. Push out the handset hook and reattach in opposite direction for the wall mount position, plug the coiled cord into the handset, and then plug the other end of the cord into the case. 4. Place the handset on the base. 5 TELEPHONE PART IDENTIFICATION Flash Switch 10 Hold Button Data Port 11 Flash Button Telephone Line Cord Jack 12 Redial Button Message Waiting Indicator 13 Volume Button Memory Access 14 Microphone Pause Button 15 Pulse/Tone Handsfree Button 16 Ringer Off/Low/Hi Mute Button 17 Speaker Volume Store Button 6 TELEPHONE FEATURES PULSE AND TONE DIALING 1. If your telephone line accepts a touch-tone dialing, set the PULSE/TONE switch to the Tone position. 2. If your telephone line requires a rotary (pulse) dialing, set the PULSE/ TONE switch to the Pulse position. 3. If you are unsure which system you have, set the switch to the TONE position. Lift the handset. When you get a dial tone, dial a telephone number. If the dial tone continues, move the switch to PULSE, and then dial the telephone number again. 4. If the Pulse/Tone Switch is set to the Pulse position and you want to make a tone entry after pulse dialing, press the * button once, then dial the number. RECEIVING A PHONE CALL 1. Be sure the RINGER switch is set to the HI or LOW position. 2. When the phone rings, lift the handset. 3. Set the Ringer switch to the OFF position when you do not want to be interrupted by the phone ringing. Remember to set the Ringer switch to Hi or Low when you want to receive calls again. PLACING A PHONE CALL 1. Lift the handset and wait for a dial tone. 2. Dial the telephone number you wish to call, or depress one of the 10 memory buttons. VOLUME BUTTON A built-in amplifier feature allows you to increase the listening volume in the receiver of the handset when speaking with your party. When needed, press the VOLUME button to achieve three different levels. The volume will go back to normal after you hang up the handset. REDIAL BUTTON 1. If the number you dialed i...