Login:
Votes - 2, Average rating: 5 ( )

User manual Binatone, model CAPRICE CAPRICE 600

Manafacture: Binatone
File size: 2.72 mb
File name: caprice-600.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


Locating the Base unit The Base unit should be placed on a level surface, in a position where: .. the mains adapter plug will reach an easily accessible 230-V AC switch mains supply socket - never try to lengthen the mains power cable. .. the telephone line cable will reach your telephone line socket or extension socket. .. it is not close to a sink, bath or shower, or anywhere else where it might get wet. .. it is not close to other electrical equipment - fridges, washing machines, microwave ovens, TVs, fluorescent lights, etc. 2. Plug the coiled handset cord into the Handset. Plug the other end into the jack on the left side of the Base unit. 3. Place the Handset in the Base unit. 4. Plug the telephone line cord into the PHONE LINE jack at the back of the Base unit. Plug the other end into a modular wall jack. 5. Plug the power supply cord into the POWER jack at the back of the Base unit. Plug the other end to a 230 V AC, 50 Hz mains socket, with the switch on the socket set to OFF. 6. Switch ON the mains power at the socket. 7. Lift the Handset and check for Dial tone in the earpiece. Always use the telephone line cord supplied with your Caprice 600. Other telephone line cords may not work. The Caprice 600 Base unit must be used only with the supplied mains adapter. Using any other adapter may damage the unit. 4 Note: The Base unit does not require a battery. 3. Desk/Wall mount installation 5 To place the Caprice 600 on a desk, connect the stand to the bottom of the phone in the slots near the ringer cover as shown below. Desk Mount Insert the rigid clips of the stand into the slots on the bottom of the phone (near the ringer cover). Press down firmly until the flexible clips clicks into place. To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward (3) as shown below. To place the Caprice 600 on a wall, connect the stand to the bottom of the phone in the slots near the battery cover as shown below. Wall Mount Binatone Help Line - 0845 345 9677 Calls are charged at Local Call rate. 6 Desk/Wall mount installation continue... Insert the rigid clips of the stand into the slots on the bottom of the phone (near the battery cover). Press down firmly until the flexible clips clicks into place. To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward as shown below. Mark two points on the wall that are 137mm apart to lay the fixing centers as shown below. BE CAREFUL to check that there are no electrical wires hidden in the wall. Fix two screws (supplied with the unit) at the marked locations, leaving approximately 7mm between the wall and the the screw head. Hang the cradle unit on the screws using the wall mount slots. You may need to remove the telephone from the wall and tighten the screws so that the cradle is securely fixed and does not wobble. Place the Handset on the cradle with the parking hook on the cradle arranged to fit in the parking recess under the earpiece on the Handset. 7 4. Setting up the Caprice 600 The following section details how to set up your telephone. Press the MENU button to enter the Options menu and then use the UP or DOWN buttons to cycle through the following options: .. SET LANGUAGE .. SET TIME/DATE .. SET FLASH TIME .. LCD CONTRAST .. MESSAGE LENGTH .. RINGS TO ANSWER .. REMOTE ACCESS .. EXIT OPTION Note: The system will time out if you leave ! more than 15 seconds between key presses. With the phone in standby mode; 1 Press MENU button. ..The display shows OPTIONS MENU . 2 Press UP button to go to the language setting. ..The display shows SET LANGUAGE. 3 Press MENU button to confirm. 4 Press UP or DOWN button to select ENGLISH (default), FRANCAIS, or ESPANOL. 5 Press MENU button to confirm. 6 Continue with programming, or press EXIT button to return to standby mode. SET LANGUAGE 1 Press MENU button. ..The display shows OPTIONS MENU . 2 Press UP or DOWN button until the display shows SET TIME/DATE. 3 Press MENU button to confirm. .. The ‘year’ icon will be blinking. SET TIME/ DATE Binatone Help Line - 0845 345 9677 Calls are charged at Local Call rate. Setting up continue... 8 4 Press UP or DOWN button to set the year. 5 Press MENU button to confirm. .. The ‘month’ icon will be blinking. 6 Press UP or DOWN button to set the month. 7 Press MENU button to confirm. .. The ‘date’ icon will be blinking. 8 Press UP or DOWN button to set the date. 9 Press MENU button to confirm. .. The ‘hour’ icon will be blinking. 10 Press UP or DOWN button to set the hour. .. When setting the ‘hour’, the ‘AM’ or ‘PM’ icon will automatically turn ON to correspond the hour time. 11 Press MENU button to confirm. .. The ‘minute’ icon will be blinking. 12 Press UP or DOWN button to set the minute. 13 Press MENU button to confirm the TIME and DATE setting. 14 Continue with programming, or press EXIT button to return to standby mode. 1 Press MENU button. ..The display shows OPTIONS MENU . 2 Press UP or...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category