062310-JA info@elitescreens.com Kestrel Accessories Kestrel Accessories Qty 1 Radio Frequency Remote Control Qty 1 Infrared Remote Control Qty 2 AAA batteries Qty 1 Qty 1 Qty 1 5-12V Trigger Low Voltage 3-way IR “eye” Receiver Wall Switch IMPORTANT SAFETY NOTES 1. Please read this manual before use and follow the procedures specified: a. Please retain this manual for future reference. b. To avoid any damages to the screen, do not use any accessories or parts not recommended by Elite Screens. c.

Please follow the pre-cautions below for proper care procedures and to prolong the life of your StarBright7. Failure to comply will result in voiding your warranty. Avoid using any chemical compounds or harsh abrasives which will result in permanently damaging the screen material. • USE ONLY a soft non-abrasive cloth with mild soap and water to clean the screen material • DO NOT rub the cloth with force when cleaning to avoid permanently scratching the surface • DO NOT touch the screen surface w

1. Frame Parts x 6 pcs (4 Top & Bottom frame pcs + 2 Side frame pcs) 2. Tension Rods x 6 pcs (4 Top & Bottom frame rods + 2 Side rods) 3. Screen Material x 1 pc 4. Center Joints x 2 pcs 5. Elbow Joints x 4 pcs 6. Wall Brackets x 2.3 pcs (depending on size) 7. Screws x 16 pcs 8. User Guide x 1 pc 9. Center Support Bar x 1.2 pcs (depending on size) 10. Support Joiner x 2.4 pcs (depending on size) 11. Fix Plates x 30.90 pcs (depending on size) 12. Black Cloth Backing x 1 pc (AcousticPro 1080 models

It can be adjusted in both length and height to optimize the right level of projection. SPECIFICATIONS Max weight for ceiling and wall installation. 37.4 lbs. Total weight of the A56.E25B2. 3 lbs. Overall dimensions of the A56.E25B2. (L x W x H) 12.5” x 4.3” x 2.3” ExampleofA56. E25B2asashort. throwmountforwallinstallation. ExampleofA56.E25B2withoutextensionbarforaflushmounttotheceiling. ExampleoftheA56.E25B2withextensionbarforhighorangledceilings. Rev.030111.AS info@elitescreens.com 2 Flush Cei

060809-JA info@elitescreens.com Tripod Screen Parts Identification Tripod Screen Parts Identification Top Hook, Keystone Eliminator & Screen Handle Support beam Vertical Extension Bar Screen Material Screen case Carrying handle & Screen height adjustment lock/release tab Tripod junction Tripod Support Legs End cap Vertical locking sleeve ring Using the Screen A. Setting up the screen: Follow the steps below and Fig. 1 & 2. 1. Place the screen in an upright position (fig.1) with the legs toward t

Elite Screens In-Wall Switch Module ( ZIW-Module ) m W Gray (Up) Ethernet (RJ45) network cable Blue(Down) Local wall switch Yellow(Common) Elite in-wall UP/DOWN switch module (ZIW-Module) Elite Electric/Motorized Screen Steps to attach Elite Screens Motorized Screen to your local wall switch 1. Attach Elite Screens in-wall switch module (Part #: ZIW-Module) to your local wall switch as shown in diagram above 2. Attach an RJ-45 Ethernet cable (not included) to the ZIW-Module and the ot

Bracket Hook Black Masking Border Edge Small support rod Locking sleeve White projection surface Lock Bottom Black Masking Big support rod Box Cover Note: Middle foot available on 120” models and above only. Box Foot Base Back Base anchor (available on models 120” and above only) Adjustable up to 1” Adjustment screw for leveling Attention: -Please install the two telescoping support rods simultaneously when pulling up and retracting the screen material. -Do not use the screen in a very strong wi

For the best results and maximum product longevity, ALWAYS and ONLY use Elite Screens high density whiteboard Eraser. 2. Please use the microfiber cloth and clean water to cleanse the surface every 2-4 weeks to maintain a fresh and clean projection suface. ELITE SCREENS a. c. d. e. b. Insta-DE Screen User’s Guide Adhesive Dry-Erase Front Projection Screen Parts List QTY a. Insta-DE Screen Material 1 b. Pen holder 1 c. Whiteboard pens 3 d. Elite special high density whiteboard eraser 2 e. Microfi

a. b. c. d.e. Parts List QTY a. Insta-DEM Screen Material 1 b. Pen Holder 1 c. Whiteboard markers 3 d. Elite special high density eraser 2 e. Microfiber cleaning cloth 1 Notes: 1. For Best results and maximum product longevity, ALWAYS and ONLY use Elite Screens High Density Whiteboard Eraser. 2. Please use the microfiber cloth and clean water to cleanse the surface every 2.4 weeks to maintain a fresh and clean projection surface. Rev.040611.AS info@elitescreens.com Installation Installation NOTE

Canvas Bag x 11 2. PicoScreen x 11 How DDo I Set Up The PicoScreeen? 1. Tuurn the bottoom feet to a 990 degree anggle as shown below. Rev.051311.AAS info@@elitescreens.com 2. Hold the base of the PicoScreen with one hand and grip the top handle with the other hand, pull up until the locking mechanism is securely locked into place. How Do I Retract the Pico Screen? 1. Use both hands to retract the PicoScreen. One hand should be under the case and the other on the top to push the retract button. C