Consult a qualified installer for any additional hardware necessary. SPECIAL NOTE ON CEILING MOUNT LOCATION This kit’s attachment plate is designed so that the projector and lens system form an average center of mass (gravity) approximately located at the center of the ceiling mount pipe. As a result, the ideal location for the ceiling mount is 2” (50mm) to the left of the horizontal screen center. If the ceiling mount is already installed it may be an easier alternative to shift the screen to the right by this same amount. If the entire system is already installed then the third alternative is to use the necessary amount of horizontal lens shift to compensate. This shift will cause a slight amount of horizontal keystoning through the Panamorph lens but may be small enough (especially at longer throw ratios) to overscan into the border of the screen. Also, be sure that you do not install the projector at an extreme end of its zoom range otherwise you may not have enough zoom for adjustment of the final image. Kit Components—See Page 4 STEP ONE - CONNECT THE ATTACHMENT PLATE: Place the Attachment Plate over the projector ceiling mount holes as guided by the Attachment Plate diagram. Now insert a 5/8” plastic spacer between the projector and the Attachment Plate at each of the four mount holes. Insert and tighten an M4x30mm silver screw through a M4 lock washer, M4 flat washer, the Attachment Plate and then the spacer into each of the projector’s mounting holes. Page 1 ELPALK2 ATTACHMENT PLATE DIAGRAM WARNING! Use extreme caution and appropriate hardware when installing heavy objects to a ceiling. Periodically check all fasteners and connection hardware to be sure they are not coming loose. When installing or adjusting a ceiling mount, DO NOT use adhesives to prevent the screws from loosening and do not use oils or lubricants. If you apply adhesives to the mount to prevent the screws from loosening, or if you use lubricants or oils on the projector, the projector case may crack and the projector may fall from its ceiling mount. This could cause serious injury to anyone under the mount and could damage the projector. Improper installation, or use of oils or lubricants, may lead to an increased risk of your equipment becoming unstable and possibly injuring someone. Panamorph, Inc. assumes no liability for injury or damage. Page 2 Plate STEP TWO - MOUNT THE MOTORIZED TRANSPORT: Position the flat side of the ATH Transport against the bottom side (projector side) of the Attachment Plate so that the Transport connector jacks are toward the projector Motorized Transport and the center “M” hole in the Attachment Plate is aligned with the front recessed Pivot screw as #10-32x5/8” screw (1) assembled transport hole. Insert the #10-32 x 5/8 #10-32 nut (1) pivot screw up through the Transport and Attachment Plate and loosely complete Attachment #10-32 lock washer (1) the assembly with the corresponding washer, lock washer and nut. Now #10-32 washer (1) loosely insert the four small 3/8” screws through the four remaining “M” slots through the top of the Attachment Plate #6-32x3/8” screw (4) Transport and down into the Transport. STEP THREE – PREP THE RPA ATTACHMENT SCREWS: Insert a black socket head screw through a silver 3/8” spacer into each of the six threaded holes in the top of the Attachment Plate. Insert these screws only enough to reach through to the bottom of the Attachment Plate. STEP FOUR – MOUNT THE PROJECTION ASSEMBLY: Ensure that the RPA mount head is secure and oriented properly relative to the Attachment Plate RPA screws so that the mounted projector will face the screen. Use two people to lift and position the projection assembly so that the heads of each of the Attachment Plate RPA screws rest within the matching final location of the RPA mount head. At this point the silver 3/8” spacers should be between the Attachment Plate and the RPA mount head. The projection assembly may be lowered to allow the RPA screw heads to rest on the RPA mount. However, one person should continue to support the projection assembly while a second person uses the gold hex key wrench to tighten the RPA screws. When tightening the RPA screws, do so in a pattern of incrementally driving each screw a little more into the attachment plate so that at any time the projection assembly is resting on as many screw heads as possible until all are tightened. STEP FIVE – INSTALL THE LENS: Refer to the Transport user manual for additional instructions to install the lens at this time. REMEMBER TO COMPLETE THE LAST STEP BELOW. STEP SIX – FINAL ADJUSTMENTS: a. Turn the projector on with the anamorphic lens out of the projector beam. Set the horizontal lens shift to neutral and then adjust the RPA mount so that the 16:9 image is in the exact center of and square to the screen with a similar amount of image slightly over the top and bottom screen borders. If the projector lens is not in the exact horizontal center of the screen you may need t...