Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Cat5 or better with a RJ45 connector. .. Many network connection problems during set up can often be fixed by re-setting the router or modem. After connecting the player to the home network, quickly power off and/or disconnect the power cable of the home network router or cable modem. Then power on and/or connect the power cable again. .. A 10 Base-T or 100 Base-TX LAN port is required for connection to this Projector. If your internet service does not allow for such a connection, you will not be able to connect the Projector. .. To connect to the wireless router, a router that supports wireless connection is necessary, and the wireless connection function of the corresponding router must be activated. .. To connect to a wireless router, verify the SSID and security setting of the wireless router. Please refer to the user guide of the corresponding router for SSID and security setting of the wireless router. .. When Ad-hoc is used, it may not be able to connect according to the device (for example : notebook computer) that is connected. .. The connection method may vary according to the manufacturer of the wireless router. < How to connect > Connect the LAN of the projector and the LAN port of the PC or network with a LAN cable (Cross cable). LAN Cable LAN AUDIO IN LAN AUDIO IN < PC > LAN Cable < Router > Connecting PC USB < How to use > 1. Press the MENU button. Then, move to OPTION with the ., .,<,> buttons and press the .OK button. 2. Press the ., . buttons to move to Network Setting and press the .OK button. 3. Press the<,> buttons to move to On of LAN option. OPTION Menu Language : English Blank Image : Blue Screen Capture Lamp Mode : Normal Monitor Out : RGB1 Set ID : 1 Network Setting High Altitude : Off 3D Mode .Move .OK Close IP Auto Setting IP Manual Setting Network does not exist. Do you want to reset? LAN . Off . 4. Press the ., . buttons to move to IP Auto Setting or IP Manual Setting press the .OK button. < When select IP Manual Setting > • In most cases, you should select Auto. If you are using a router it will automatically .Move .OK IP Address set the IP address. . 1 9 2 1 6 8 0 0 0 2 5 4 • Select IP Manual Setting for ordinary PC. . Subnet Mask - Setting PC: Set the Internet Protocol (TCP/IP) of the PC at your own discretion. 2 5 5 2 5 5 2 5 5 0 0 0 Setting Projector: Set IP Address as the IP Address format of PC, and select Close Gateway after entering the Gateway as the same Gateway of PC. Please refer to eZ-Net 1 9 2 1 6 8 0 0 0 0 0 1 Manager Guide for details of network setting. :: example :: IP Address Subnet Mask Gateway PC 192.168.0.10 255.255.255.0 192.168.0.1 Projector 192.168.0.254 255.255.255.0 192.168.0.1 Close • If Network Setting is not working, check your network conditions. Check the LAN cable connection. • If the Network Setting is not completed, network functions may not operate normally. • IP Auto Setting: Select it if there is a DHCP (Dynamic Host Configuration Protocol) server on the local area network (LAN) via wired connection, the Projector will automatically be allocated an IP address. The IP address will automatically be determined. Connection to DHCP may not be possible when the fire- wall is installed or according to the model of the computer. IP Manual Setting: Select it if there is no DHCP server on the network and you want to set the IP address manually. • Press the BACK button to exit the menu screen. High Altitude Mode * High Altitude Mode is used when the environment is higher than 1200 meters. 1. Press the MENU button. Then, move to OPTION with the ., .,<,> buttons and press the .OK button. 2. Press the ., . buttons to move to High Altitude and press the .OK button. 3. Press the<,> buttons to move to On and press the .OK button. • Press the BACK button to exit the menu screen. OPTION Menu Language : English Blank Image : Blue Screen Capture Lamp Mode : Normal Monitor Out : RGB1 Set ID : 1 Network Setting High Altitude : Off 3D Mode .Move .OK INFORMATION Menu Options To See The Projector Information 1. Press the MENU button. Then, move to INFORMATION with the ., .,<,> buttons and press the .OK button. 2. You can see the current information of the projector. • Press the BACK button to exit the menu screen. INFORMATION Model Name : BX327-JD Lamp Time : 12 Hr Input : RGB1 Resolution : 1024 x 768 Fh/Fv : 48.36 Khz/60 Hz IP Address : 223.212.145.0 USB USB * Image shown may differ from your projector. To use the USB device Connecting the USB device * When you connect a USB device, this screen is displayed, automatically. In USB device, you can not add a new folder or delete the existing folder. 1. Connect the USB device to the USB jack on the back of the set. 2. It turns automatically to DivX Home Menu. Eject USB PHOTO LIST MUSIC LIST MOVIE LIST FILE VIEWER USB memory stick * Select “Eject” in order to eject a USB device. 1. Press the Q.MENU button on the remote control. 2. Press the<,> buttons to move to USB Device. 3. Press the .OK button on the remote control...