Votes - 2, Average rating: 4
(
)
)
|
manual abstract
This does not mean that all of these devices can or must be connected simultaneously. (Dotted lines mean items can be exchanged.) Audio cable / (not supplied) supplied) Video recorder, DVD player, etc. Computer DVD video recorder, etc. To audio output White (L)/ Red (R) Audio cable (not supplied) rvideo I S-video s-vldeo cable T output output (not supplied) 1 '- ' To RGB RGB cable (supplied) y \ Audio cable (not supplied) Conversion adapter AAA BNC-pin (not supplied) -if V V ToY/Cb/Cr Red To audio ouput Monitor cable Mini D-sub 15P-BNC (not supplied) Audio cable (not supplied) ____________ To audio ouput White (L)/ Red (R) To audio intput White (L)/Red (R) To RS-232C terminal fflEEV Audio amplifier, etc. Computer (for control) Monitor It is necessary to switch to MONITOR OUT by the switch. I3& * The connection for COMPUTER 1 IN terminal described here Is also applicable for COMPUTER 2 IN terminal. 22 r Notes • When COMPUTER 2 IN terminal is used as MONITOR OUT terminal, the signal which is input to COMPUTER 1 IN terminal is output. • Signals are output from MONITOR OUT terminal even in standby mode. However, from AUDIO OUT terminal, no audio signal is output. • A computer monitor cannot accept Y/Pb/Pr signals correctly. • The AUDIO IN terminal can be used for devices connected to COMPUTER 1 terminal, COMPUTER 2 terminal, VIDEO terminal and S-VIDEO terminal. • When an AUDIO OUT terminal is connected, sound is not output from the projector speaker. • Output volume of AUDIO OUT terminal can be adjusted by the VOL button. 23 Preparations Turning the power on and off ■ Connecting the power cord 0 Insert the power cord connector into the AC IN socket of the projector. 6 Insert the power cord plug into a wall or other power outlet. The ON/STANDBY indicator will change to orange, indicating standby mode. Power cord connector (Supplied) I Turning the power on ) Removing the lens cap Be sure to remove the lens cap when the power is turned on. If the cap is left on the projector, it could become deformed due to heat. Control panel Remote control © Press the ON/STANDBY button. The power turns on with a beep sound (if the beep sound is set to [On]), and the ON/STANDBY indicator flashes green. After a moment, the start-up screen appears. A CAUTION Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyesight. Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating. Do not place your hands, face, or other objects near the air exhaust, the lamp cover or the bottom of the unit. Doing so could result in injury and/or damage the object. r Notes • The start-up screen will disappear after a moment. You can configure the system to prevent the start-up screen from appearing. To do this, use the Display setting menu ES&. • The first time you use the projector after purchase, after the start-up screen disappears, the start menu is displayed row* • You can disable the beep sound in the Default setting 1 menu EBi>- • When [Key lock] is [On], the operation buttons of the projector do not work HRV • When [Password] is [On], enter password then the start-up screen is displayed after the Password entry screen disappears HEE» • Do not touch the lens directly with your hand. If fingerprints or stains are left on the projection lens surface, they may interfere with the projector’s ability to project images on the screen. 24 ■ Turning the power off 0 Press the ON/STANDBY button. When the setting of beep sound is [On], the projector beeps, and a message appears on the screen, confirming that you wish to shut off the power. To shut off the power, press the ON/STANDBY button again. If you do not wish to shut off the power, wait for a while without conducting any operations. This message will disappear after a moment. (This operation is no longer valid after the message disappears.) 0 Press the ON/STANDBY button again. When the setting of beep sound is [On], the projector beeps, and the screen disappears, but the internal cooling fan continues to operate. Then, the projector goes into standby mode. During cooling, the ON/STANDBY indicator flashes. While the indicator is flashing, the power can not be turned back on. There is no problem with unplugging the power cord in this state. 0 Replace the lens cap. After use, replace the lens cap. r Note • The projector consumes about 4.5W of power in standby. We recommend that you unplug the power cord if you will not be using the projector for an extended period. r Precautions • When you wish to restart the projector again right after turning off the power, give the lamp time (about 5 minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light. • Right after turning off the power, the unit may become very hot, especially air exhaust, lamp cover or the bottom of the unit. Please handle with care to avoid burn i...
Other models in this manual:Projectors - TLP-X100U (3.37 mb)