Votes - 3, Average rating: 5 ( )

Manafacture: Toshiba File size: 1.72 mb File name: Language of manual:

Doing so could cause malfunction. • Note that when extending or rotating the camera arm, the arm moves in an arc. Take care not to bump yourself or others with it. Preparing the document camera (for use being separated from the projector) • Before connecting the camera cable, make sure that the projector power is off. PRECAUTIONS • Insert a camera cable straight and securely until it locks. When disconnecting the cable, pull it out releasing the lock on both sides of the plug. • Be sure to pull the tip resistant bar fully until it forms the angle of 90 degree. If you don’t use the bar, the camera may topple over. • Note that the camera may tip over if you attempt to rotate the arm in the opposite side of the tip resistant bar. • For camera interconnection, be sure to use the supplied camera cable (1 m). If you use the other cables, the normal operation cannot be achieved and even the malfunction may result. Note • Connecting or disconnecting the camera cable with the projector's power ON may cause camera error ( is displayed) and even turn off the power. Status before preparation (When stowed) 1) Set up arm 2) Extend arm 3) Rotate arm 4) Raise camera head 1) Connect the supplied camera cable to the camera input terminal. 2) Connect the other end of the camera cable to the camera terminal on the document camera. 3) Pull out the tip resistant bar and set up the document camera. Using the document camera Please read this chapter if the model you purchased includes a document camera. Uninstalling the camera Installing the camera PRECAUTIONS • Before mounting or dismounting the document camera, disconnect the power plug. • Place a soft cloth beneath the projector when mounting or dismounting the camera. • Do not dismount or mount the document camera while the projector is upright or kept in the air. • Before mounting the camera, confirm that the interconnection connector is closed with the connect lever. If you attempt to mount the camera with the connector being protruded, connector may be damaged. • When mounting the camera, be sure to slide the document camera until it is locked with click sound. • Confirm the four registration stays are aligned before sliding the camera. 1) Place the folded document camera with the bottom side up. 2) Slide the connect lever in the direction of an arrow. 3) Pressing the lock lever in the direction of an arrow, slide the document camera. 1) Place the folded document camera with the bottom side up. 2) Align the four registration marks. 3) Slide the document camera in the direction of an arrow until it clicks. 4) Slide the connect lever in the direction of an arrow. Using Image projection 1 Place the document. Set the document at the 2 Press the CAMERA button, and select camera • The input returns to the previous input when the CAMERA button is pressed again. • Camera input can also be selected by pressing the remote control or camera’s INPUT button. 3 Rotate the camera lens to align the orientation of the document shooting. 4 Move the camera head up and down to adjust the image size. Farther: Smaller image Closer: Larger image • Closeup shot with the distance shorter than 100 mm cannot be performed. 36 5 Adjust the focus Rotate the focus ring NEAR or FAR, whichever is better Turn the focusing ring to adjust the focus. • Near : 100 mm to 300 mm Far : 300 mm to 5 m 6 If the screen is too dark or too bright, CAMERA GAIN (+/ – ) buttons to make it easier to see. The Sharpness of the camera image can also be adjusted the Image adjustment menu p.32 . 7 After use, turn off the light, and fold up the document camera. Fold up the camera using the opposite order from Preparation of the document camera. PRECAUTION • If the room’s fluorescent lighting causes the image to flicker, either turn off the fluorescent light, or set the Shutter speed from the Default menu p.32 . Note that changing the Shutter speed setting may not eliminate the flicker, depending on the lighting, state of the document, or image adjustment. Note • No audio is output when camera input is selected. 37 Operations Using Locking the Although the projector’s camera is constantly it photographs, the color the document, etc. If this below. 1 Lay down a piece of white and adjust so it fills the screen. Adjust the camera head and arm so the screen completely. 2 Set the White balance to Lock in the Default menu. p.32 The white balance is locked. If you want to return to the auto adjustment, White balance to Auto in the Default menu. Notes • White balance setting to Fixed, if power is turned off, will be back to Auto. • The color of the room lighting may prevent the white balance from being adjusted optimum level. In this situation, or if you want to use a certain tinting, adjust the R-level, G-level and B-level on the Image adjustment menu p.32 . Maintenance Air filter The air filter prevents Never run the • The icon message projector with the “ Check the air filter for ” is displayed every 100 usage time exceeds 100 dis...

Download now

Please, enter two numbers from picture: