Votes - 4, Average rating: 3.8 ( )

Manafacture: Toshiba File size: 8.25 mb File name: Language of manual:

[Background] • TOSHIBA is set for [Logo] by factory setting. 34 Using the menus (Continued) ¦ The default setting menu This menu shows placement status and other settings. Item Description Projection mode Sets projection mode in accordance with Placement Style. (Standard) (Rear) (Ceiling) (Rear ceiling) Auto input search Set whether the input with signals is only selected or not. On Off Language Select one of the languages below to use for displaying the menu and messages [ : Enter setting mode] [ :Selection] [Apply: ] English/Francais/Deutsch/Italiano/Espanol/Portugues/ /Svenska/Turkce/Polski/ / / / Start-up screen Display start-up screen when power is turned on On Off Fan mode Sets the cooling fan speed. Standard High Lamp power Sets the lamp power. Low Standard Password Password function p.30On Off When [Password] is [On], the Password Setting screen is displayed. Power on Sets whether to turn on the power when the ON/STANDBY button is pressed (Manual), or when the power cord is plugged in (Auto). Manual Auto p.22 Detailed description [Fan mode] Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to use the projector, for example, at high altitude (over 1,500 meters above sea level). [Lamp power] When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling fan noise gets quieter. Operations 35 Using the menus (Continued) ¦ Displaying Information (Status display) This displays information about the input signal, lamp use time, etc. “Yes”: displayed, “No”: not displayed Item Input Resolution Video mode Picture mode Lamp time Version Description Input source name Resolution (in dots) Color method of video signal A group of Pre-set display mode Time of lamp use [Note 3] Firmware version [Note 4] Computer Y/PB/PR Video S-video Yes Yes Yes Yes Yes No No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Notes 1: The mode of supported RGB signals p.44 is shown. 2: Sync signal polarity shown as P (positive) or N (negative) for [H/V]. 3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult with a store about getting a TLPLV6 replacement lamp (sold separately) prepared. 4: [Version] shows the version of the projector’s internal control program. This version is referred to for customer service, etc. 36 About lamp The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure to fully understand the following characteristics of the lamp and handle it with extreme care. • The lamp may burst with a loud noise due to impact or deterioration, or fail to light at the expiration of its life. • How long it takes before the lamp bursts or the life expires may vary greatly by lamp. Some may burst shortly after first use. • Burst is likely to happen if the lamp is used after the replacement period has elapsed. • When the lamp bursts, the broken pieces of glass may get inside the product or be released outside from the openings for ventilation. • When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with glass dust may be released from the openings for ventilation. ¦ Immediately replace the lamp when a sign appears on the screen. • When the replacement time approaches, a message will appear on the screen. • The risk of burst will increase if the lamp is continuously used without being replaced. • Frequently check the used hours and prepare spares when the replacement time approaches. (Refer to “Status display”. p.36 ) ¦ When the lamp is broken • If glass components, including a lamp and a lens, should break, handle the broken pieces with care to avoid injury and contact your dealer for repair service. • In the event of lamp burst, unplug the product from the wall outlet, leave and completely ventilate the room. Then, thoroughly clean the area around the projector and discard any edible items placed in that area. • When the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes or you breathe it. Lamp replacement A lamp is consumable supplies. If used for extended periods, images will appear dark, and the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime of the lamp depends on condition of use.) If this happens, replace it with a new one. WARNING • If the projector is mounted on the ceiling, it is recommended to use your Toshiba dealership when the lamp has to be exchanged. Uncovering the lamp while the projector is mounted on a ceiling may lead to a danger of damage from falling pieces of glass if the lamp is broken. Besides, working at high elevations can also be hazardous. Do not attempt to replace the lamp by yourself. • When replacing, always use lamp “TLPLV6” (sold separately). CAUTION • If you have been using the projector, the lamp will be very hot, and may cause burn injuries. Wait for the lamp to cool...

Download now

Please, enter two numbers from picture: