Votes - 2, Average rating: 4 ( )

Manafacture: Toshiba File size: 1.99 mb File name: Language of manual:

¦ Turning the power on 1 Turn on the main power switch The ON indicator will change to orange, indicating standby mode. 2 Press the ON/STANDBY button. The power turns on, and the following 3 green indicators light: ON, LAMP, and FAN. After a moment, the start-up screen appears. Start-up screen Control panel Remote Control Power cord connector (Supplied) CAUTION • Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes or sight. • Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating. • Do not place your hands, face, or other objects near the air exhaust. Doing so could cause burns, deform/break the object. ¦ Removing the lens cover Be sure to remove the lens cover when the power is turned on. If it is left on, it could become deformed due to heat. (Orange) T urning wer on ued) Turning on Notes • The start-up screen will disappear You can dismiss the up screen before this by performing any operation. You can also configure up screen not to appear via the Display setting menu p.30 . • The first time you use the projector after purchase, after the start-up screen disappears, the Language menu is displayed p.23 . ¦ Turning the power off 1 Press the ON/STANDBY button. A message appears on the screen, confirming that you wish to shut off the power. This message will disappear after a moment. (This operation is no longer valid after the message disappears.) 2 Press the ON/STANDBY button again. The screen turns off, but the internal cooling fan continues to operate for a short while. Then, the projector goes into standby mode. When cooling lamp During internal cooling After cooling complete B C(Orange) (Orange) (Green) (Off) (Off) (Off) (Green) (Green) Flashing (Orange) A A B During cooling, the LAMP indicator flashes. In this state, the power cannot be turned back on. After the LAMP indicator goes off, the cooling fan continues to operate for a short while, in order to expel excess internal heat. If you are in a hurry, there is no problem with unplugging the power cord or turning off the main power switch in this state. In standby mode Note • The projector consumes about 12W of power in standby. We recommend that you unplug the power cord or turn off the main power switch if you will not be using the projector for an extended period. PRECAUTION • If the power cord is unplugged before cooling is complete, give the lamp time (about 5 minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light, and its lifetime will be shortened. 22 Basic 1 Turn on the Turn on the power by following the instructions in “ Turning the power on” p.21 . 2 Select the language and the lamp power (When using first time). When the projector is used for the first time after purchase, menu for language and lamp power selection and configuration is displayed in English. (If the screen is out of focus, adjust it according to the step 6.) English q Use the or button to select the French desired language and press the button. German Message for setup confirmation is displayed in a Italian Spanish Por tuguese selected language. Then, the menu for lamp power selection and Russian configuration is displayed. It is automatically set as Swedish Standard. To change the setting, follow the step w. Turkish Japanese w Using the or button, select Low or Chinese (simplified) Standard for the lamp power (menu item) Chinese (traditional) Korean and press the button. The lamp power, if selected, will be toggled without pressing the button. The display automatically disappears in a few seconds. Notes • When the projector is turned on the next time, the Language and Lamp power menus do not appear upon startup. However, if “ Reset all” is executed from the Default setting menu p.31 , the Language and Lamp power menus will be displayed the next time when the power is turned on. • The language can also be set via the Display setting menu p.30 and Lamp power via the Default setting menu p.31 . • This owner’s manual assumes that English has been selected. 3 Activate the connected device. Turn on and start the connected device such as a computer. 4 Press the INPUT button. An image of the connected equipment is projected. Each time you press the INPUT button, it switches to the input of the connected equipment. Notes • When [ Auto input search] is set to [ On] in the default setting menu p.31 , the image of the equipment which is connected and turned on is projected. •Moving pictures generated with the DVD software for computers may appear unnatural if it is projected with this projector, but it is not a malfunction. 23 Operations 25 Operations 24 ¦ Using auto setting This function sets up the projector to the optimum state for each type of the input signal by using simple operations. 1 Press the SET UP button. The Set up menu appears. 2 Press the SET UP button again. The displayed menu item is automatically adjusted/set. For computer input, the ic...

Download now

Please, enter two numbers from picture: