Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
Furthermore, the remote control unit can be operated from an angle of ±30 ° to the left or right and ±15 ° above or below the receptors. NOTE: • If there are any obstacles in between the remote control unit and the receptors, the remote control unit may not operate correctly. • If strong light is allowed to shine onto the remote control signal receptor, correct remote control operation may not be possible. Place the projector as far away from light sources as possible. • If facing the remote control unit toward the screen to operate the projector, the operating range of the remote control unit will be limited by the amount of light reflection loss caused by the characteristics of the screen used. w Connections Notes on connections • Read the instruction manual for each system component carefully before connecting it. • Turn off the power supply for all components before making any connections. • If the cables necessary for connecting a component to the system are not included with the component or available as an option, you may need to fashion a cable to suit the component concerned. • If there is a lot of jitter in the video signal which is input from the video source, the picture on the screen may flicker. In such cases, it will be necessary to connect a TBC (time base corrector). • The projector has built-in speakers. However, you will need to connect a separate audio system to the AUDIO OUT jack if your needs specify high sound volumes. No sound will come out of the projector’s built-in speakers while the AUDIO OUT jack is being used. • It may not be possible to connect some types of computer. Refer to the list of compatible signals on page 50. • The pin layout and signal names for the S-VIDEO IN connector are shown below. Pin No. Signal © Ground (Luminance signal) CD Ground (Color signal) CD Luminance signal © Color signal • The pin layout and signal names for the RGB/YPbPr (RGB1 IN/RGB2 IN) connector are shown below. Pin No. Signal © R/Pr CD G/G-SYNC/Y CD B/Pb © SDA © H D/SYNC © VD © SCL Pin (D is spare. Pins (gHD, © and © are for ground. Pins @ and © functions are only valid when supported by the computer 17 Preparation Example of connecting with video equipments Computer for control use D-sub 15 (male) - BNC5 (female) adapter cable (sold separately) Red (connect to Pr signal connector) Blue (connect to Pb signal connector) Green (connect to Y signal connector) Digital broadcast tuner or DVD player Audio system Video deck Laser disc player NOTE: • Only one audio system circuit is available for the AUDIO IN L-R jacks for S-VIDEO/VIDEO signals, so if you wish to change the audio input source, you will need to remove and insert the appropriate plugs. • Only one audio system circuit is available for the RGB AUDIO IN jacks, so if you wish to change the audio input source, you will need to remove and insert the appropriate plugs. • If an audio system is connected to the AUDIO OUT jack, the sound volume balance can be controlled by the remote control unit which is supplied with the projector. • If the video signal source is connected using a cable with a BNC connector plug, use a BNC/RCA adapter (sold separately) to convert the cable end to an RCA plug-type jack. • Refer to page 50 for a list of compatible YPbPr signals which can be input to the projector. • If the signal cables are disconnected or if the power supply for the computer or video deck is turned off while the digital zoom or index window functions are being used, these functions will be cancelled. 18 Example of connecting with computers Computer Computer Computer for control use D-sub 9-pin (male) Audio system NOTE: • If the MAIN POWER switch for the projector is turned off, it’s better to shut down the computer also. • Refer to the list of compatible signals on page 50 for the types of RGB signals which can be input to the projector by connecting a computer. • Only one audio system circuit is available for the RGB AUDIO IN jacks, so if you wish to change the audio input source, you will need to remove and insert the appropriate plugs. 19 Preparation Setting-up Projection methods The projector can be set up so that any one of the following four projection methods are used. Select whichever projection method matches the settingup method. (The projection method can be set from the Option menu. Refer to page 37 for details.) DESK/CEILING DESK CEILING FRONT/REAR FRONT —■A ------^ A (Factory default setting) REAR ft :: ~ - A ~ .A NOTE: • You will need to purchase the separate ceiling bracket (ET-PK701) when using the ceiling installation method. Projector position 'Top edge of screen \ Screen Bottom edge of screen "Ta L: Projection distance SH: Image height SW: Image width H1: Distance from center of lens to bottom edge of projected image (SH *10) 20 Projection distances Screen size (4:3) Projection distance (L) Height position (H1) Diagonal l...