Login:
Votes - , Average rating: ( )

User manual InFocus, model SP-CEIL-010

Manafacture: InFocus
File size: 1.08 mb
File name: 10369634-da28-0c14-8d82-d99b102cd433.pdf

Language of manual:en

The document is loading, please wait
The document is loading, please wait

manual abstract


E. SINGLE WOOD STUD: If mounting on a single wood stud use three (3) #14 x 2" Lag bolts (minimum) commercially available. Use the mounting points on the center of the plate as indicated in the assembly diagram. ° SOLID STRUCTURE: If mounting to a solid structure use four (4) 5/16" x 2" Lag bolts or commercially available hardware (depending on the installation requirements). Use the mounting points found on the outer points of the mounting plate as indicated in the assembly diagram. F. Allen wrench (supplied) 1 (4) Solid structure mounting points (2) Cable access points (2) Tension knobs Screen side (Yellow indicator) Clamp plate Safety knobs (Red indicator) Ceiling plate Tools Needed for Installing the Digital Projector Mount You need the following tools to install the Digital Projector Mount: • Phillips head screwdriver (not included) • Allen wrench (included) • Drill (for installation environment only - do not use a drill on the Digital Projector or the Digital Projector Mount) and drill bit to match the hardware for your installation environment (not included) • The commercially available hardware (E) that is required by your installation environment (not included) Getting the projector ready Before you start the installation process, prepare your Digital Projector by performing the following steps (FIGURE 1). 1. Turn the projector (C) upside down and place it on a clean flat surface, preferably on a towel. 2. Locate the mounting bracket (B) and align it over the holes on the projector. 3. Locate the four (4) 6 (mm) x 10 (mm) Phillips head screws (A). 4. Use the Phillips head screwdriver to secure the mounting bracket (B) to the projector via the three (3) Phillips head screws (A). Do not over-tighten the screws. FIGURE 1 A C B (Optional) Fixed Height Ceiling Installation Complete the following steps to install the projector mount and projector on your ceiling. This installation works best with low ceilings (FIGURE 2). Note: Look at the bottom of the mount assembly (D) and locate the arrow. Make sure you install the projector mount with the arrow pointing toward your screen. 1. Remove the upper plate from the assembly (D) secure to the ceiling structure using the commercially available hardware (E) suitable for your environment. Be sure that the mount assembly screen indicator arrow is pointing toward your screen. 2. Replace the mount assembly with the upper plate and fully raise the safety knob and tension knobs all the way. Carefully raise the projector (C) with the mounting bracket (B) attached and insert it into the bottom of the mount assembly (D) by its tabs. 3. Rotate the projector (C) with the mounting bracket (B) attached 180. so that the projector’s focus ring is pointing toward your screen. 4. Align the safety knob on the mount assembly (D) with the end of the arrow-shaped slot on the mounting bracket (B) and screw it through the opening to prevent further rotation. Hand-tighten the safety knob. 5. Hand-tighten the remaining two tension knobs to secure the mounting bracket (B) to the mount assembly (D). CAUTION: Check all of the hardware for proper tightness and security. Do not over-tighten the screws. Lightmount Plus® Overview Lower assembly 2 (3) Single wood stud mounting points Adjustable extension Ceiling plate Remove (M8) Hex head screws, flat washers and star lock washers Remove the center extension from the assembly Remove (M8) Hex head screws, flat washers and star lock washers Replace the ceiling plate Replace (M8) Hex head screws, flat washers and star lock washers Bottom assembly Ceiling structure Wood stud Center of wood stud D E C B A E Solid ceiling structure D C C B A Insert and rotate 180° and lock down Insert and rotate 180° and lock down 3 Adjustable Height Ceiling Installation Complete the following steps to install the projector mount and projector on your ceiling with the optional suspension adapter. This installation works best with high ceilings (FIGURE 3). Note: Look at the bottom of the upper assembly (D) and locate the arrow. Make sure you install the projector mount with the arrow pointing toward your screen. 6. Use the Allen wrench (F) to remove the upper plate from the mount assembly (D). 7. Use the Allen wrench to remove the two screws from the enclosed end of the of the suspension adapter, and place it into the slotted extension on the upper plate (E). Make sure that the two (2) outer holes on the suspension adapter align with the holes on the slotted extension on the upper plate. 8. Replace the two screws removed in step 2 into the two (2) holes to secure the suspension adapter to the upper plate. 9. Attach the mount assembly to the suspension adapter and secure them with the two screws removed in step 1. 10. Secure the upper assembly to the ceiling using the commercially available hardware (E) suitable for your environment. Be sure that the upper assembly arrow is pointing toward your screen. 11. Carefully raise the projector (C) with the mounting bracket (B)...

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category