Votes - 0, Average rating: 0 ( )

Manafacture: Philips File size: 2.92 mb File name: Language of manual:

If this is not the case, push the control lever up and down again to enter the alarm time mode.You can also set the alarm time in the menu. See section ‘Menu functions’ in this chapter. 3 ,4 5 Press the SELECT button to confirm (Fig. 10). The minute indication of the alarm time starts to flash (Fig. 15). Press the menu + and - buttons to select the minutes (Fig. 9). Press the SELECT button to confirm or wait for a few seconds (Fig. 10). The appliance leaves the menu and the display shows the clock time. , The alarm time is now set. switching off the alarm To switch off the alarm function, push up the control lever to the top position. Note:The lamp stays on to light your room.You can switch off the lamp by pressing the light on/off button. Note:The alarm (sound and/or light) automatically switches off after 90 minutes. setting the alarm sound See section ‘Menu functions’ above. You can choose one of the following sounds: -Radio (Fig. 16) -Birds (Fig. 17) -Beep (Fig. 18) -Wind chimes (Fig. 19) snoozing 1 Push down the control lever to the bottom position when the alarm goes off (Fig. 20). The lamp continues to be on at the selected intensity level, but the alarm sound stops. , After 9 minutes, the wake-up sound is automatically played again. Note:The 9-minute snooze time is fixed.This time cannot be adjusted. Note: If you push down the control lever with too much force, it may jump back to off position. 10 EnglisH alarm demonstration If you want to get a quick demonstration (60 seconds) of the gradually increasing light level and sound level, activate the test function of the appliance. 1 2 Push the control lever down to the bottom position for a few seconds until TEST appears on the display (Fig. 21). Push the control lever down again to stop the demonstration. Note:The appliance continues to run the alarm demonstration until you push down the control lever again.The test automatically stops after 9 hours. radio/volume 1 To switch on the radio, press the radio on/off button (Fig. 22). 2 To select the desired radio frequency, press the menu + and - button (Fig. 9). Tip:To scan radio frequencies automatically, press and hold the menu + or - button for approx. 2 seconds. Tip:To make sure you get a good radio signal, fully unwind the antenna and move it around until you have found a position at which reception is best. To switch off the radio, press the radio on/off button again. volume To set the volume, press the volume increase or decrease button (Fig. 23). 3 1 You can choose a volume level between 1 and 20. Note:The volume level you have selected is automatically set as the volume level for the alarm as well. sunset simulation You can use the sunset simulation function if you want the light and/or the sound of the Wake-up Light to stay on and dim gradually during a set period of time (15 minutes to 1.5 hours) before you go to sleep.The lamp and/or sound switch off automatically after the set time. 1 Switch on the lamp and/or the radio. See sections ‘Using the lamp’ and/or ‘Radio/volume’ in this chapter. Note: If neither the lamp nor the radio is on when you activate the sunset simulation function, then only the lamp goes on. 2 Follow steps 1 to 5 in section ‘Menu function’ in this chapter to select the sunset simulation function and to set the sunset simulation time (Fig. 24). You can choose a time from 15 to 90 minutes (15 minutes, 30 minutes, 45 minutes, 1 hour or 1.5 hours). After the set time, no matter whether only the light and/or the radio are on, the sunset , simulation function switches off both light and sound. Tip: you can also press the lamp on/off button for more than 3 seconds to activate the sunset simulation function. setting the display brightness Follow steps 1 to 5 in section ‘Menu function’ in this chapter to select the display brightness function and to increase or decrease the display brightness (Fig. 25). You can choose a display brightness between 1 and 4. EnglisH 11 cleaning and maintenance Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance. Regularly remove dust from the outside of the appliance with a dry cloth. 1 2 Unplug the appliance before you clean it. Clean the outside of the appliance with a dry cloth. Do not let water run into the appliance or spill water onto the appliance (Fig. 3). replacement Except for the lamp, the appliance does not contain any ser viceable par ts. The lamp has to be replaced when it stops burning or when the light output decreases (also see chapter ‘Impor tant’).You must replace the lamp with a Philips Halogen lamp, 100W, 12V, GY6.35. Only this lamp provides the correct light intensity. Note:This appliance has been designed to be used with self-shielded lamps only (Fig. 26). For more information, see chapter ‘Guarantee and ser vice’. replacing the lamp 1 Unplug the appliance before you replace the lamp. 2 Let the appliance cool down for approx. 15 minutes. 3 Unlock the top cover o...

Download now

Please, enter two numbers from picture: