Votes - 4, Average rating: 4.5 ( )

Manafacture: Invacare File size: 2.14 mb File name: Language of manual:

• Always ensure the XPO2 internal and supplemental external batteries are recharged as soon as possible afterthey become fully discharged. The batteries may be permanently degraded if left fully discharged for an extended length of time. •Check the status of your XPO2 internal and supplemental external battery once a month if you are not using yourXPO2 regularly. Both batteries should be maintained at 2 illuminated bars worth of charge. •Heat is the worst enemy of a battery. Allow plenty of air to circulate around the XPO2 so that the battery is kept as cool as possible when charging and also when in use. Invacare XPO2™ 26 Part No 1148112 SECTION 6—OPERATING INSTRUCTIONS Don’ts •DO NOT use or leave the XPO2 or supplemental external battery in excessive heat or cold. •DO NOT store or leave the XPO2 or supplemental external battery in car trunks, etc. for extended periods of time. •DO NOT store either battery fully charged (4 barsilluminated on the unit’s battery gauge) if you are going to store your XPO2 for any time greater than 2 weeks. Recharge or discharge the battery to 2 bars (50% charge) only. Storing a battery with a full charge may degrade itsuseful life. •DO NOT leave your supplemental external battery plugged into the XPO2 when the XPO2 is not in use. The supplemental external battery will lose charge whileplugged into the XPO2 even with the XPO2 turned off. Battery Gauge Battery Status Button Supplemental Battery Pack Illuminated Bars FIGURE 6.6 Prolonging XPO2 Battery Life Part No 1148112 27 Invacare XPO2™ SECTION 6—OPERATING INSTRUCTIONS Powering the XPO2 NOTE: Both the internal and supplemental battery require full charging prior to first use. Refer to Charging the Batteries on page 22. NOTE: For this procedure, refer to FIGURE 6.7 on page 29. 1. TheXPO2allowsthefreedomtochoosefromthefollowing power sources: •The internal battery. The XPO2 comes equipped with an internal battery that is installed at the factory and is not user serviceable. •The supplemental battery pack. To use, connect the supplemental battery pack to the XPO2 as shown in Detail “A”. •ADCpoweroutlet(i.e.anautomobile).Touse,connect the DC power adapter to the XPO2 as shown in Detail “B”. Connect the other end of the DC power adapter to the DC power source. •An AC outlet (i.e. wall outlet of your home). To use, connect the AC power adapter to the XPO2 as shown in Detail “C”. Connect the other end of the AC power adapter to the AC power outlet. 2. If the XPO2 is in use and connection to an external power supply is necessary, perform the following: A. Turn off the XPO2. B. Connect the external power supply (e.g. supplemental battery pack, DC mobile power adapter, or AC power adapter) to the XPO2. C. Turn the XPO2 on. Invacare XPO2™ 28 Part No 1148112 SECTION 6—OPERATING INSTRUCTIONS DETAIL “A” - SUPPLEMENTAL BATTERY PACK XPO2 Portable Concentrator Supplemental Battery Pack DETAIL “B” - DC POWER ADAPTER XPO2 Portable Concentrator Connect to DC Power DC power Adapter source DETAIL “C” - AC POWER ADAPTER XPO2 Portable Concentrator Connect to AC Power AC power Adapter source FIGURE 6.7 Powering the XPO2 Part No 1148112 29 Invacare XPO2™ SECTION 6—OPERATING INSTRUCTIONS Connecting/Positioning the Nasal Cannula CAUTION To ensure proper breath detection and oxygen delivery, DO NOT use tubing length exceeding 25 ft (7.6 m). NOTE: For this procedure, refer to FIGURE 6.8. NOTE: Invacare recommends using the XPO2 with a 4 ft (1.2 m) cannula. The tubing must be connected to the XPO2 oxygen outlet as shown below. NOTE: Replace the nasal cannula on a regular basis. Check with your equipment provider or physician to determine how often the cannula should be replaced. NOTE: DO NOT share cannulas between patients. 1. Connect the nasal cannula to the XPO2 oxygen outlet port (Detail “A”). 2. Place the cannula over your ears and position the prongs in your nose as instructed by your health care provider or cannula manufacturer (Detail “B”). Invacare XPO2™ 30 Part No 1148112 SECTION 6—OPERATING INSTRUCTIONS Oxygen Nasal Outlet Port DETAIL “B” DETAIL “A” FIGURE 6.8 Connecting/Positioning the Nasal Cannula Adjusting the Pulse Flow Setting Cannula CAUTION It is very important to select the prescribed level of oxygen flow. DO NOT increase or decrease the flow unless a change has been prescribed by your physician or therapist. NOTE: For this procedure, refer to FIGURE 6.9 on page 32. 1. Turn On the XPO2 by pressing and holding the power On/Off button for approximately one second. Each time the XPO2 is turned On, a brief alarm will sound. The XPO2 pulse flow setting at power.up will be the same flow setting selected the last time the unit was turned Off. 2. The XPO2 has five pulse flow settings. Press the flow selection (+ or .) button until your prescribed flow setting (1 to 5) is illuminated by a blue indicator light. Part No 1148112 31 Invacare XPO2™ SECTION 6—OPERATING INSTRUCTIONS FLOW SETTING AVERAGE PULSE VOLUME (AT 20 BREATHS PER MINUTE) 1 15 ml 2 ...

Download now

Please, enter two numbers from picture: