Votes - 3, Average rating: 4
(
)
)
|
manual abstract
USA MANUAL NO. 999-0858 Warranty Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered. Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor. Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void. Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages. This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above. SEGA Service Department 45133 Industrial Drive Phone: 415.701.6580 Fremont, Ca. 94538 Fax: 415.701.6594 If you have any questions please contact the SEGA Service Department at the numbers given above. MA_ADD Before starting work be sure to turn power off. Failure to observe this can cause electric shock and short circuit hazards. Use care so as not to damage wirings. Damaged wirings can cause electric shock or short circuit accidents. This work should be performed by the Locations Maintenance Man or Serviceman. Performing work by those who do not have technical expertise can cause electric shock accident, or damage to the Game Board 1.) Turn power off & Disconnect all plugs from the Game Board Cage. 2.) Remove Cage and open Case Lid. 3.) Remove (12) phillips screws and remove the PCB from Cage. 4.) Remove (4) phillips screws and nuts that secure Security Board to CPU Board. Remove Security Board. 5.) Install new Security Board and secure with the (4) philips screws previously removed; DO NOT OVER TIGHTEN! 6.) Remove each of the (41) E-Proms and Mask Roms from the Rom Board. Be careful not to scratch the Board or break sockets. 7.) Install new E-Proms and Mask Roms. Be careful not to damage IC by static electricity. Be careful not to bend pins while inserting E-Proms and Mask Roms. 8.) Re-install Game Board into cage, then replace cage into cabinet. Reconnect all connectors. 9.) Power On Game and test for proper operation. Set all game options. KIT INSTALLATION INSTRUCTIONS: Please see diagrams on the following page for E-PROM and ROM layout. EMERGENCY CALL AMBULANCE ROM CHANGE INSTRUCTIONS SEGA Service Department 45133 Industrial Drive Phone: 415.701.6580 Fremont, Ca. 94538 Fax: 415.701.6594 If you have any questions please contact the SEGA Service Department at the numbers given above. MA_ADD Before starting work be sure to turn power off. Failure to observe this can cause electric shock and short circuit hazards. Use care so as not to damage wirings. Damaged wirings can cause electric shock or short circuit accidents. This work should be performed by the Locations Maintenance Man or Serviceman. Performing work by those who do not have technical expertise can cause electric shock accident, or damage to the Game Board 1.) Turn power off & Disconnect all plugs from the Game Board Cage. 2.) Remove Cage and open Case Lid. 3.) Remove (12) phillips screws and remove the PCB from Cage. 4.) Remove (4) phillips screws and nuts that secure Security Board to CPU Board. Remove Security Board. 5.) Install new Security Board and secure with the (4) philips screws previously removed; DO NOT OVER TIGHTEN! 6.) Remove each of the (41) E-Proms and Mask Roms from the Rom Board. Be careful not to scratch the Board or break sockets. 7.) Install new E-Proms and Mask Roms. Be careful not to damage IC by static electricity. Be careful not to bend pins while inserting E-Proms and Mask Roms. 8.) Re-install Game Board into cage, then replace cage into cabinet. Reconnect all connectors. 9.) Power On Game and test for proper operation. Set all game options. KIT INSTALLATION INSTRUCTIONS: Please see diagrams on the following page for E-PROM and ROM layout. EMERGENCY CALL AMBULANCE ROM CHANGE INSTRUCTIONS [ CURRENT E-PROM AND MASK ROM LAYOUT ]* Your game board may differ from the one pictured below [ NEW EMERGENCY CALL AMBULANCE E-PROM AND MASK ROM LAYOUT ] * Items that are marked with and asterick are not provided with this kit, but may be purchased through your SEGA authorized parts dealer for your game. COMPOSITION OF GAME BOARD (game board not included) Ensure that the DIP SW setting is performed as designated as designated. Failure to observe thisw may cause functioning not suitable ...