Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Switch and Forward/Reverse
LED light
How to use the belt hook
To change the belt hook
lever Operation
CAUTION:
WARNING:
location side
The built-in LED light is designed to illu-
• Be sure to attach the belt hook
The belt hook can be attached to either
minate the small work area temporarily.
securely to the main unit with the screw
side of the unit.
Do not use it as a substitute for a regular
firmly fastened. When the belt hook is
flashlight, since it does not have enough
not firmly attached to the main unit, the
brightness.
hook may depart and the main unit
may fall.
Forward
Reverse
Depress the trigger switch, then LED light
This may result in an accident or injury.
turns on. When the trigger switch is
• Be sure to attach the belt hook firmly
released, the light turns off automatically.
and securely onto a waist belt or other
belt. Pay attention to the unit not
The light illuminates with very low current,
1. Set the belt hook at storing position.
slipping off from the belt.
and it does not adversely affect the perfor-
This may result in an accident or injury.
2. Loosen the screw turning it counter-
mance of the driver during use or its bat-
clock-wise, using a coin or a flat blade
Switch lock
tery capacity.
• When the main unit is held by the belt
screw driver.
hook, avoid jumping or running with it.
CAUTION:
Doing so may cause the hook to slip
To prevent damage, do not operate
and the main unit may fall.
Forward/Reverse lever until the bit
This may result in an accident or injury.
comes to a complete stop.
• When the belt hook is not used, be
Forward Rotation Switch
sure to return it to the storing position.
Operation
The belt hook may catch on something.
This may result in an accident or injury.
1. Push the lever for forward rotation.
• When the unit is hooked onto the waist
3. Take out the belt hook and insert into
2. Depress the trigger switch slightly to
belt by the belt hook, do not attach
the other side of the slot on the main
start the tool slowly.
driver bits to the unit.
unit.
3. The speed increases with the amount
A sharp edge object, such as a drill bit,
4. Fasten the screw firmly, turning it clock-
of depression of the trigger for efficient
may cause injury or an accident.
wise.
tightening of screws. The brake oper-
ates and the bit stops immediately
To set the belt hook angle
The belt hook can be taken out from the
when the trigger is released.
position
main unit only when it is at storing position.
4. After use, set the lever to its center po-
1. Slide the belt hook lock lever # and
sition (switch lock).
hold it to unlock the belt hook.
Reverse Rotation Switch
2. Pull the belt hook from
Operation
storing position $ and
This product has the built-in LED light.
set it as desired angle.
1. Push the lever for reverse rotation. Check
This product is classfied into “Class 1 LED
3. Release the belt hook
the direction of rotation before use.
Product” to EN 60825-1.
lock lever to lock the
2. Depress the trigger switch slightly to
angle of belt hook.
CLASS 1 LED PRODUCT
start the tool slowly.
4. Make sure the belt hook is firmly locked
3. After use, set the lever to its center po-
%. Also make sure the belt hook is firmly
sition (switch lock).
Caution: DO NOT STARE INTO BEAM.
locked into position.
CAUTION:
• The belt hook cannot
be locked in this posi-
To eliminate excessive temperature
tion. Firmly lock it into
increase of the tool surface, do not oper-
position before use.
ate the tool continuously (using two or
To return the belt hook to the storing
more battery packs consecutively.) Tool
position, Follow step 1. and 2. above, then
needs cool off time before switching to
lower the belt hook.
another pack.
To secure the lock, follow 3 and 4 above.
– 6 –
– 7 –
...