Votes - 2, Average rating: 4
(
)
)
|
manual abstract
BDL300S BEFORE RETURNING THIS PRODUCT FOR ANY REASON PLEASE CALL 1-800-544-6986 SAVE THIS MANUAL FOR FUTURE REFERENCE. IF YOU SHOULD HAVE A QUESTION OR EXPERIENCE A PROBLEM WITH YOUR BLACK & DECKER PRODUCT, CALL 1-800-544-6986 BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., TYPE No., AND DATE CODE (e.g. 20000130M). IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER. VEA EL ESPANOL EN LA CONTRAPORTADA. INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. 586017-00 BDL300S laser 7/30/03 8:51 AM Page 2 WARNING: Read and understand all CAUTION: Use of controls or 2 1 2 3 INSTALLING THE BATTERY Ensure laser on/off switch is in the left “OFF” position. Remove the battery compartment cover by pressing the tab of the cover in towards the center of the laser and out as shown in figure 3. Connect a fresh 9 volt alkaline battery making sure to match (+) and (-) terminals correctly. Replace the battery compartment cover. ASSEMBLY / SET-UP UNFOLDING THE LASER LEGS To open the 360° Laser: 1.) Choose a relatively smooth and level surface away from other work site activity to position the tripod. 2.) Unfasten the strap that is around the outside portion of the laser and unfold the three sections of the laser housing which become the legs of the tripod. 3.) Lock the legs in place, by pushing in on the top portion of the hinge until it snaps into place as shown in figure 4. CAUTION: Make sure tripod is secure and sitting on a flat and stable surface. ADJUSTING THE TRIPOD The tripod is adjustable from its lowest position of approximately 27 inches (686mm) shown in figure 5 to a maximum height of 5 feet (1524mm) shown in figure 6. Extend any or all of the 5 sections of the tripod to reach the approximate desired height. Extend each section by gently sliding each tube out until it stops and then pull slightly harder on each section to lock. When the approximate desired height is obtained, use the fine adjust knob shown in figure 8 to raise the laser to the final desired height. The fine adjustment knob will raise the laser up to an additional 7 inches (178mm) high. First, loosen the lock knob as shown in figure 7. Turn the fine adjust knob (figure 8) until the desired height is reached. Tighten the lock knob (fig. 7) to secure the tripod at the adjusted height. 3 4 5 6 7 8 Lock Knob Fine Adjust Knob 586017-00 BDL300S laser 7/30/03 8:51 AM Page 3 586017-00 BDL300S laser 7/30/03 8:51 AM Page 4 Make sure laser is securely fastened. HANGING THE LASER 9 The laser can also be hung from a joist or other secure structure using the hanging strap included. CAUTION: Make sure laser is securely suspended by the strap. To hang, thread the strap through the slot in the top of the laser and fasten the hook as shown in figures 10 and 11. Adjust the laser so that it hangs relatively straight. The self-leveling function will then compensate for any minor error. LASER OPERATION • Before attempting to use the laser, make sure the tool is positioned on a relatively smooth, flat and stable surface. • To increase working distance and accuracy, set up the laser in the middle of your working area. Brightness of area may effect line visibility. • When attaching to the tripod or using the hanging strap, mount the laser securely. • Be aware that extreme temperature changes can cause movement or shifting of building structures, tripods, equipment, etc. which can effect accuracy. Verify your set-up before each use as the laser may have moved. • This product is not recommended for outdoor use. TURNING THE LASER ON 12 To turn the laser on, slide the lower on/off switch shown in figure 12 to the right. OPERATING IN SINGLE 120° LASER MODE To operate the laser using a single laser beam, slide the upper switch to the left as shown in figure 13. 13 OPERATING IN 360° LASER MODE To operate the laser using all 3 laser beams, slide the upper switch to the right as shown in figure 14. 14 10 11 4 586017-00 BDL300S laser 7/30/03 8:51 AM Page 5 T TTTTR RRRRO OOOOU UUUUB BBBBL LLLLE EEEES SSSSH HHHHO OOOOO OOOOT TTTTI IIIIN NNNNG GGGG Problem • Laser does not project on wall. Possible Cause • The self leveling range for the level line is +/- 5°. Solution • Position tripod ona relatively smooth and level surface. • Line only visible on one wall. • Switch in 120° mode. • Move switch t 360° mode. • Laser beam dim. • Weak battery. • Replace battery STORAGE To store the unit, reattach the laser to the top of the tripod making sure that it snaps into place securely. Loosen the locking knob, turn the fine adjust knob to its lowest setting and return the tripod to its lowest position. Unhinge the legs and fold them into the center. Reattach the strap around housing. Always store the laser indoors and in its closed state with the switch in the “OFF” pos...