Votes - 4, Average rating: 3.3
(
)
)
|
manual abstract
2. Using the tabs on the back of the front cover, pop the cover plate off the unit. (Figure 1) Label the 2 sensor wires from the thermostat with the included wire labels, being sure to match the polarity of the sensor wires at the thermostat. 3. Pull the labeled wires through the opening on the sensor back housing. (Figure 2) Secure the sensor to the wall with the 2 screws provided, and level for appearance using the bottom corners. 4. Strip a bare end on each wire approximately 1.4” long, and bend to a small hook. Place behind the screw and washer for each terminal that matches the labeled wire, and tighten securely. (Figure 3) Snap the front cover onto the back housing. NO TE: When using shielded wire, connect the shield to the NEGATIVE terminal at the remote sensor and thermostat. (RS–, RS1– or RS2–) Polarity MUST be followed for the sensor to work. The RS+ and RS- terminals must match the corresponding sensor 1 or 2 terminals on the thermostat, ei-ther RS1+ and RS1- or RS2+ and RS2-. NO TE: For shorter distances (up to 100 ft. / 30m), standard or twisted pair wire may work on Heat Pump systems. For longer distances, multi-stage systems, or any site with electrical noise, use 20 gauge shielded wire. OPERATION Refer to the instructions included with the Climate Technology thermostat for more details. 1. Turn power back on to the system, and be sure the thermostat is powered. 2. Within a minute, the thermostat will display “ Found RM1” and/or “ Found RM2”. This means that the thermostat is communicating properly with the remote sensor. After locating the sensor, if the thermostat has a problem communicating with the sensor, “ Check RM1” or “ Check RM2” will appear. 3. Press the OPTION key on the thermostat to select the weighting for the Local and remote sensor(s), and to see the measured temperature for each sensor. 4. If there is a problem with the installed remote sensors, then the Local sensor reading will be used for the temperature. TROUBLESHOOTING If the remote sensor is not working, check these items: 1. Confirm the polarity matches between the remote sensor and thermostat. Also check that the wires for the sensor go to corresponding sensor 1 (RS1) or sensor 2 (RS2) terminals. 2. If using standard wire, change to 20 gauge shielded wire. Be sure the shield is connected to the negative terminals. 3. Confirm the wires are held firmly in place at the terminals on both the sensor and thermostat. If you experience any other problems, call 1-800-676-7861 from 8 AM to 5 PM Central Time for technical assistance. Tab Figure 1 ESPECIFICACIONES ¦ Sensor remoto de temperatura ¦ Conexion de 2 alambres, no requiere alimentacion electrica separada ¦ Rango de medicion: 15° F a 99° F (-9° C a 37° C) ¦ Exactitud: +/- 1° F (+/- 0.5° C) ¦ Maxima distancia de conexion: 100 m (328 pies) con cable blindado de 2 conductores calibre 20 ¦ DEBE mantenerse la polaridad entre el sensor y el termostato SOLO PARA USO EN INTERIORES Solo para uso con los siguientes modelos de termostatos Climate Technology: 43058, 43558 INSTALACION NO T A : Corte la alimentacion al sistema antes de empezar la instalacion. Todo el cableado debe cumplir los codigos electricos locales y nacionales. Consulte las instrucciones del termostato Climate Technology para obtener detalles sobre el cableado del termostato. Siga las instrucciones en el paso 4 al conectar los alambres del sensor a los terminales en el termostato. 1. Ubicacion: Monte el sensor a 1.5 metros del piso, solamente en una pared interior. No ubique el sensor donde sea afectado por corrientes fuertes de la puerta o los ductos, o de la luz solar directa u otras fuentes de calor. 2. Usando las lenguetas de la parte posterior de la cubierta delantera, retire la placa de cubierta de la unidad. (Figur...