Votes - , Average rating:
(
)
)
Manafacture: Harbor Freight Tools
File size: 11.7 mb
File name: 93601.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
Page 2 10. Always check hardware and assembled parts after assembling. All connections should be tight and hardware tightened. 11. Caution: Avoid sharp edges during use and assembly. 12. Beware of operating the power tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or sawdust. Electrical products create sparks which may ignite sawdust released from the Dust Collector, as well as other dust and fumes. 13. Carefully inspect the condition of the accessory before use and check the accessory continually during use. If any damage is noted, stop immediately and replace the accessory with an undamaged one. Harbor Freight Tools cannot be held responsible for damage caused by using a damaged accessory on this product. 14. Keep the hoses away from sharp objects and excessive heat. 15. Make sure to read and understand all instructions and safety precautions, as outlined in the manufacturer’s manual of the power equipment to which the Dust Collector Accessory Kit will be attached. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activites, contain chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm. some examples of these chemicals are: • Lead from lead-based paints • Crystalline silica from bricks and cement or other masonry products • Arsenic and chromium from chemically treated lumber Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code 25249.5, et seq. ) Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking your Dust Collector Accessory Kit, check to make sure all parts listed on page 5 are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353. Product Overview The Dust Collector Accessory Kit is designed to be attached to one or two power tools, and is used Accessory Kit may be attached to table saws, band saws, sanders, router tables, shapers, jointers, for the collection of wood dust, wood chips, sand, and other light debris. The Dust Collector and a variety of dust collecting machines all having a 4” dust port. Due to the wide diversity of power machinery to which the Dust Collector Accessory Kit may be attached, it is recommended that onlya qualified technician perform the assembly procedure. SKU 93601 For technical questions please call 1-800-444-3353. Page 3 Assembly Assembly . Though the Dust Collector Accessory Kit is designed to offer a wide variety of applications, the following illustration depicts a typical assembly method to hook-up one power equipment tool and two power equipment tools-see Figure 1 below. 2. Note: The Dust Collector Accessory Kit is designed to be attached to stationary power equipment tools and dust collectors having 4” diameter dust ports. Depending on the diameter of the dust port of your power equipment tools and dust collector, it may be necessary to attach size adapters (not included) to ensure a proper fit. Power Tool Power Tool Dust Port Jointer Hood (6” square) (3) or Table Saw Dust Hood (12’ square) (5) 4” Diameter Blast Gate (2) Flexible Hose (1) 4”Wire Hose Clamp (6) Dust Port Dust Collector “Y” Fitting (4) Figure 1-To Attach to One or Two Power Tools Attaching to Two Power Tools Attaching to One Power Tool 3. Check the length of Flexible Hose (1) needed to set up the Dust Collector Accessory Kit with your power tool. It may be necessary to cut the Flexible Hose (1). To cut the Flexible Hose (1), cut the plastic on the hose in a straight line between one coil of wire. Use a tin snip or wire cutter to cut the coil inside the hose. 4. Place a Wire Hose Clamp (6) over the Flexible Hose. Slide the Flexible Hose (1) onto the dust port. Slide the Wire Hose Clamp (6) so that it sits on both a section of Flexible Hose (1) and the dust port. Thread down the screw on the Wire Hose Clamp (6) until the Flexible Hose (1) is tight on the dust port. 5. Open and close the Blast Gate (2) to control the air flow from the Power Tool(s) to the dust collector. When this kit is attached to 2 power tools, always close the Blast Gate (2) of an unused dust collector hose. SKU 93601 For technical questions please call 1-800-444-3353. Page 4 Inspection, Maintenance and Cleaning Inspection, Maintenance and Cleaning . CAUTION: Prior to performing any inspection, maintenance, or cleaning of the Dust Collector Accessory Kit, make sure to turn OFF and then disconnect the power tool ...