Votes - 3, Average rating: 3.3
(
)
)
|
manual abstract
. Pull the bit holder. (2) 3. Insert the bit. (3) 4. Make sure the bit is inserted firmly by pulling it lightly. 5. Insert the bit adapter into the mounting hole and turn to locate an engaged position. Bit holder 6. At the engaged position, push in as far as it goes. • Make sure it does not move by pulling it lightly. - Forward/Reverse Lever ReverseForward Lock Be sure to set the switch in the center to lock it after use. Operate the Forward/Reverse lever after the motor rotation is completely stopped. Hammering/Drilling Switching Lever NOTE: Operate the mode change after the motor rotation is completely stopped. Position of Action mode switching lever Rotation with hammering Rotation only Operation Concrete Drilling, Block Drilling Screw Fastening, Metal Drilling Clutch Torque Setting Adjust the torque to one of the 5 clutch settings or “ ” position. CAUTION: Test the setting before actual operation. Set the scale at this mark ( ). Variable Speed Control TriggerTo set the center of a hole, pull the trigger slightly to start the drill rotation slowly. The more the speed control trigger is pulled, the higher the speed becomes. 5 EY6803(EU).indb 5 9:41:30 2006/04/10 Shoulder pad Shoulder pad LED Light CAUTION: • The built-in LED light is designed to illuminate the small work area temporarily. • Do not use it as a substitute for a regular flashlight, since it does not have enough brightness. switch, then LED light turns on. When the trigger switch is released, the light turns off automatically. The light illuminates with very low current, and it does not adversely affect the performance of the tool during use or its battery capacity. Depress the trigger This product has the built-in LED light. This product is classified into “Class 1 LED Product” to EN 608 5-1 Class 1 LED Product Caution : DO NOT STARE INTO BEAM. Installing the Shoulder Strap CAUTION: • Install the shoulder strap firmly to the main unit of the tool and check the length of the strap before use. • Check the condition of the strap and do not use if it is cut or torn etc. There is a risk of injury or damage if used while improperly installed. • Please wear the shoulder strap securely on the shoulder. There is a risk of injury or damage if it is accidentally dropped. 1. Pass the strap through the strap holders. (1) . Pass the strap through the buckles and adjust the length. (2) • The shoulder strap can be adjusted according to the individual. • Adjust the shoulder pad to the shoulder. • Pull the shoulder strap to make sure it is firmly attached to the main unit of the tool. For Appropriate Use of Battery Pack Ni-MH Battery Pack (EY9201) • Charge the Ni-MH battery fully before storage in order to ensure a longer service life. • The ambient temperature range is between 0°C (3 °F) and 40°C (104°F). If the battery pack is used when the battery temperature is below 0°C (3 °F), the tool may fail to function properly. In that case, charge the battery until charging is completed for appropriate functioning of the battery. • When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns or a fire. • When operating the battery pack, make sure the work place is well ventilated. Battery Pack Life The rechargeable batteries have a limited life. If operation time becomes extremely short after recharging, replace the battery pack with a new one. -6 EY6803(EU).indb 6 9:41:31 2006/04/10 NOTE: Use under extremely hot or cold conditions will reduce operating capacity per charge. Battery Recycling For environmental protection and recycling of materials, be sure that it is disposed of at an officially assigned location, if there is one in your country. Battery ChargerNOTE: Charge a new battery pack, or a battery pack that has not been used for a prolonged time, for about 4 hours to bring the battery up to full charge. Battery charger (EY0110) 1. Plug the charger into the AC outlet. NOTE: Sparks may be produced when the plug is inserted into the AC power supply, but this is not a problem in terms of safety. . Insert the battery pack firmly into the charger. Battery pack To AC outlet Battery charger 3. During charging, the charging lamp will be lit. When charging is completed, an internal electronic switch will automatically be triggered to prevent overcharging. • Charging will not start if the battery pack is warm (for example, immediately after heavy-duty operation). The orange standby lamp will be lit until the battery cools down. Charging will then begin automatically. 4. When charging is completed, the charging lamp will start flashing quickly in green color. 5. When in any of the conditions that battery pack is too cool, or the battery pack has not been used for a long time, the charging lamp is lit. In this case charging takes longer to fully charge the battery p...