Votes - 4, Average rating: 4
(
)
)
|
manual abstract
READ AND KEEP FOR REFERENCE. INSTRUCTIONS Rev. D Supercedes Rev. C Pressure Roller Equipment 300 psi (21 bar) MAXIMUM WORKING PRESSURE Operate your pump at the lowest pressure needed for sufficient paint supply to your roller Adjustable Extension Roller Kit 218–625 Includes Roller Frame, 18–36 in. Extension Tube, 3/8 in. nap Roller Cover and 45 Gun Adapter Adjustable Extension Tubes 218–775 18–36 in. (0.45–0.9 m) 218–776 3–6 ft (0.9–1.8 m) 218–777 6–12 ft (1.8–3.7 m) *45 Gun Adapter 218–932 1/4 npt(m) x 7/8 UNF(F) *Flush Kit 218–944 Uses standard garden hose to flush water– base paints from the Extension Tube and Roller Frame *360 Straight Swivel 218–931 1/4 npt(m) x 1/4 npsm(f) swivel *Gun Adapter Kits for non–Graco guns 218–945 For guns with 3/4–20 nozzle threads (Binks) 218–946 For guns with 1–1/16–16 nozzle threads (Wagner) Tip Gaskets 218–600 Package of 5 tip gaskets *See packaging for specific installation instructions NOTE: For a leak–free connection, use pipe sealant on all male threads. 05881 Roller Cover & Roller Frame (See Manual 307–755 for parts) Adjustable Extenstion Tube 360 Straight Swivel 45 Gun Adapter Tip Gasket Gun Adapter Kit Flush Kit Graco Gun Graco Inline Dispensing Valve GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 COPYRIGHT 1995, GRACO INC. Graco Inc. is registered to I.S. EN ISO 9001 WARNING INSTRUCTIONS EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury. . Do not modify the tube or roller frame or use parts not designed for this equipment. . If the adjustable extension tube starts to extend during use, stop rolling immediately and engage the gun safety latch. Check that the locknut on the tube is tight. If the locknut is tight, the tube or the roller is clogged; follow the Pressure Relief Procedure on page 3 and flush throughly. . Use the adjustable extenstion tube only with the roller frame described in this manual. This is not an airless gun extension (pole gun). FIRE AND EXPLOSION HAZARD Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury. . Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid being applied. . Keep the application area free of debris, including solvent, rags, and gasoline. ELECTROCUTION HAZARD Avoid contact with power lines. Contact with power lines could cause serious injury, including burns or electrocution. . Follow all grounding instructions in your separate pump and paint gun instruction manual. . Comply with all local, state, and national fire, electrical, and safety regulations. Adjustable Extension Tubes 218–775 18–36 in. (0.45–0.9 m) 218–776 3–6 ft (0.9–1.8 m) 218–777 6–12 ft (1.8–3.7 m) Screw Includes replaceable item 108–163, shaft seal. Tube Washer Seal Lips of seal must face into tube; grease before assembly; do not damage lips Handle Apply Loctite Note: Always flush the extension tube as instructed in Flushing on page 3. Wetted parts: Stainless Steel, Polyurethane, Plated Steel Ring 05882 Fig. 1 ..................... ADJUSTABLE EXTENSION ROLLER KIT 218–625 Installation 1. Assemble the roller kit as shown in Fig 2. Be sure the gasket is in place between the gun and adapter. 2. Extend the tube to the desired length and tighten the locknut securely. NOTE: Always allow cold equipment to warm to room temperature before using. Operation 1. Be sure the fluid drain valve is closed and the gun safety latch is engaged. Then start the pump and set it to the lowest possible operating pressure. 2. Disengage the gun safety latch and trigger the gun briefly until paint comes to the roller. 3. Experiment with triggering and rolling the paint until you determine just how often you need to trigger the gun to keep an even flow of paint to the roller. 4. Increase the pump pressure only if you cannot get a sufficient supply of paint to the roller. 5. To adjust the extension tube while painting, engage the gun safety latch. Loosen the locknut and extend or retract the tube. If retracting, some paint in the tube will be pushed out to the roller. Either roll this excess paint onto the wall, or completely retract the tube, drain the excess paint into a pail, then adjust the tube length. Tighten the locknut securely. 6. Whenever you stop painting, follow the PRESSURE RELIEF PROCEDURE on page 3. Then elevate the roller end of the tube to prevent paint from draining. 7. Flush the pump, gun and extension tube immediately after each use to prevent paint from drying in the equipment and damaging it. See Flushing, below. NOTE: A Flush Kit, Part No. 218–944, can be used to flush water–base paint from the Extension Tube and Roller Frame. Instructions are on the kit package. Pressure Relief Procedure WARNING PRESSURIZED EQUIPMENT HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying accidentally. To reduce the risk of an inju...